Log:
Téléchargements : 1   Taille : 437 kb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

(Picture 10) 5. Lock the gear shaft by putting a pin provided or screwdriver through the aligned keyholes in the gear case cover and the gear case. Use a socket wrench to tighten the blade-mounting bolt. Rotate bolt counter clockwise to tighten. (Picture 11) 6. Split the bracket, install the wheel assembly to the tube, and clamp it at the position best for your job, using two screws. (Picture 12 and 13) 7. You can replace loop handle with the U-shaped handle that comes with your Edge Trimmer Att

Téléchargements : 0   Taille : 1 mb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

X Check that the stop switch works correctly. X Check that the handle and handlebar are undamaged and secured correctly. X Check that the cutting attachment does not rotate at idle. X Clean the air filter. Replace if necessary. X Check that the guard is undamaged and not cracked. Replace the guard if it has been exposed to impact or is cracked. X Check that the trimmer head is undamaged and not cracked. Replace the trimmer head if necessary. X Check that the locking nut of the cutting equipment

Téléchargements : 3   Taille : 3 mb   Fabricant : Husqvarna  
Catégorie : Clippers
@name@name@name@name@name@name@name@name@name@name

Keep your hands and fingers away from the switch lever (5B) while carrying the trimmer. • Nylon line continues to rotate after the trimmer has been switched off. Before Using Your 12RC 1 .Ensure the battery is fully charged. 2.(4) Adjust the steady handle to a comfortable operating position, by unscrewing the wing knob, springing the side lugs apart, moving the handle to the required position, carefully reengaging the teeth and then tightening the wing knob. (5) To Start Your 12RC 1. Press

Téléchargements : 71   Taille : 886 kb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

Check that the spark plug is fitted with a suppressor. • Clean the cooling fins on the cylinder and check that the air intake near the starter is not blocked. • Check that the bevel gear is filled with grease up to 3/4. Use special grease. • Clean the air filter. Monthly maintenance • Clean the fuel tank. • Clean the outside of the carburettor and the space around it. • Clean the fan and the area around it. • Check fuel hose for cracks or other damage. Change if necessary. • Change the fuel filt

Téléchargements : 11   Taille : 684 kb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

Push the choke control back to its original position as soon as the engine fires, and continue trying to start until the engine starts. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. Stopping The engine is switched off by moving the stop switch to the stop position. ! WARNING! The complete clutch cover and gear housing must be fitted before the machine is started, otherwise the clutch may

Téléchargements : 10   Taille : 863 kb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

123HD60 123HD65X-series Operator’s manual (EPA) Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. KEY TO SYMBOLS Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. Please read the operator’s manual carefully and make sure you understand the instruct

Téléchargements : 2   Taille : 886 kb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

Constant contact of this type can cause damage and wear to the trimmer head. Sweeping • The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and above the area to be swept and move the tool to and fro. • When cutting and sweeping you should use full throttle to obtain the best results. ! WARNING! Neither the operator of the machine nor anyone else may attempt to remove the cut material while the engine is running or the blade is rotating, as t

Téléchargements : 7   Taille : 886 kb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

If you adjust the carburettor when the air filter is dirty it will result in a leaner mixture when the filter is finally cleaned. This can lead to serious engine damage. • Carefully turn both jets, L and H, so that they are midway between fully screwed in and fully screwed out. • Do not attempt to adjust the L and H jets beyond either stop as this could cause damage. • Now start the machine according to the starting instructions and let it warm up for 10 minutes. Low speed jet L Try to find the

Téléchargements : 0   Taille : 309 kb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

The risk increases at low temperatures. Muffler The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator. CAUTION! Muffler is fitted with a catalytic converter designed to reduce harmful exhaust gases. For mufflers, it is very important that you follow the instructions on checking, maintaining, and servicing your machine. See Checking, maintaining and servicing the machine’s safety equipment section. WARNING: Mufflers fitted with catalytic converte

Téléchargements : 5   Taille : 315 kb   Fabricant : Husqvarna  
Catégorie : Clippers
@name

Muffler CAUTION! Muffler is fitted with a catalytic converter designed to reduce harmful exhaust gases. WARNING:Mufflersfittedwithcatalyticconvertersgetveryhotduringuseandremainsoforsometimeafterstopping.Thisalsoap- pliesatidlespeed.Contactcanre- sultinburnstotheskin.Remembertheriskoffire! WARNING:Theinsideofthemufflercontainchemicalsthatmaybecarcinogenic.Avoidcontactwiththeseelementsintheeventofadamagedmuffler. WARNING:Bearinmindthat: Engineexhaustfumescontaincar- bonmonoxide,whichcancausecarbo





catégories