Log:
Téléchargements : 17   Taille : 485 kb   Fabricant : Makita  
Catégorie : Clippers
@name

ie: cutting hedges or shrubs over 1/2" in diameter or foreign objects such as wires, rocks, or fences. Before trimming check work area for foreign objects such as wires, cords, glass, fences, or rocks. Be sure to remove any foreign objects from the work area. Failure to properly maintain this hedge trimmer will void the warranty. 1. Read care and safety instructions carefully before extension cord over hedge being trimmed. On 120V attempting to use this trimmer. Only after you are units, use 16

Téléchargements : 1   Taille : 2 mb   Fabricant : Makita  
Catégorie : Clippers
@name@name@name

Blow out all loose carbon with compressed air. Install muffler and gasket. Clean Contact your nearest authorized dealer. 7. Engine overheats. Insufficient oil in fuel mixture. Air flow obstructed. Mix fuel as described in starting instructions. Clean flywheel, cylinder fins and screen. 8. Engine noisy or knocking. Loose flywheel. Spark plugs incorrect heat range. Worn bearings, piston ring or cylinder walls. Tighten flywheel nut. Replace with plugs specified for engine. Contact your nearest auth

Téléchargements : 3   Taille : 4 mb   Fabricant : Makita  
Catégorie : Clippers
@name@name@name

B. Engine 1. Air Filter a. Clean the air filter before each use. Remove wing nut and air filter cover. b. Inspect the air filter and clean in warm, soapy water monthly. Dry completely before re-installing. c. If filter is excessively dirty or no longer fits properly, replace it. d. Re-install filter making sure it is seated properly. e. Re-install cover onto air cleaner case and secure with wing nut. 2. Fuel Filter Inspect for blockage when the fuel tank is low on fuel 3Muffler Equipped with a s

Téléchargements : 1   Taille : 4 mb   Fabricant : Makita  
Catégorie : Clippers

Vue de face Etape 2 AVERTISSEMENT • DANGER UN ASSEMBLAGE INCORRECT DE CE TAILLE- HAIES PEUT PROVOQUER DES BLESSURES GRAVES. VEILLER A SUIVRE TOUTES LES CONSIGNES AVEC ATTENTION. POUR TOUTE QUESTION, CONTACTER LE REVENDEUR LOCAL OU NOTRE USINE AU (215) 357-5110. B. Modeles a manche long 1. Le taille-haies Little Wonder a ete assemble en grande partie pour vous a l’usine. Aucun outil n’est necessaire pour achever l’assemblage. 2. Tirez sur la goupille a ressort du manche de 24" (61 cm) et enfilez-

Téléchargements : 7   Taille : 980 kb   Fabricant : Makita  
Catégorie : Clippers
@name

A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user -as well as damage to the tool. If in doubt, DO NOT PLUG IN THE TOOL. Using a power source with voltage less than the nameplate rating is harmful to the motor. ADDITIONAL SAFETY RULES 1. Wear hearing protection during extended periods of operation. 2. Handle the bits very carefully. 3.Check the bit carefully for cracks or damage before operation. Replace cracked or damaged bit immediatel

Téléchargements : 7   Taille : 924 kb   Fabricant : Makita  
Catégorie : Clippers
@name

343577-5 0 Wrench 10 Part No. 781003-0 *Wrench 17 Part No. 781008-0 Trimmer base assembly Part No. 122390-2 This angle-adjustable trimmer base assembly enables you to perform any angle of cham- fering with a straight bit. Cutting depth can be adjusted smoothly and precisely with a rack and pinion type of fine depth adjustment. 0 Trimmer shoe Part No. 155263-4 0 Collet cone 1/4" Part No. 763608-8 Bits STRAIGHT -Single Flute HIGH SPEED STEEL PART NO. A B C D E 7332328A 1/8 5/16 1-1/8 1 /4 1-518 ST

Téléchargements : 0   Taille : 451 kb   Fabricant : Makita  
Catégorie : Clippers

Téléchargements : 4   Taille : 832 kb   Fabricant : Makita  
Catégorie : Clippers
@name

4. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 5. Hold the tool firmly. 6. Keep hands away from rotating parts. 7. Make sure the bit is not contacting the workpiece before the switch is turned On. 8. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate improperly installed bit. 9. Be careful of the bit rotating direction and the feed direction. IO.Do not leave the tool running. Ope

Téléchargements : 1   Taille : 303 kb   Fabricant : Makita  
Catégorie : Clippers
@name

tools \°\ D0Uble lnsulati0n JLI (3707F/FC%™f/FC) Electronic Speed Control (3707FC, 3708FC) 3707/3707F/3707FC 3708/3708F/3708FC Ergonomically enhance for superior handling a operator fatigue! id red Slim size body and Lightweight but Powerful! Trimmers! A world's leading manufacturer of power tools LED Light Unit 1. Long life time : more than 10,000 H 2. Excellent dirt-proof and vibration-proof construction 3. Compact size and Lightweight 4. Maintenance Free Model - Built-in ° Job L

Téléchargements : 9   Taille : 303 kb   Fabricant : Makita  
Catégorie : Clippers
@name

Specifications Trimmer © Double Insulation Electronic Speed Control (3707FC, 3708FC) > (I Built-in Job Light (3707F/FC, 3708F/FC) ) Dimension 3707 series 3708 series 3707 3707F 3707FC 3708 3708F 3708FC Base Type Transparent base For chamfering tilt base Collet capacity 6 mm or 6.35 mm (1/4") Continuous rating Input 440 W 500 W 440 W 500 W No load speed 35,000 min'1 26,000 min'1 35,000 min'1 26,000 min'1 Overall height 204 mm (8") 308 mm (12-1/8") Net weight 1.2 kg (2.6





catégories