Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
29 Reclining button Use this button to adjust the angle of the backrest. 30 Operation Indicator Displays operational status. 31 Cover 32 Manual Operation buttons This allows you to select the massage action you desire. (See Page 13) • • • • • • • 22 21 23 24 25 26 27 28 29 30 31 32 33 34 35 Cover Closed Cover Opened CONTROLLER English SETTING UP THE UNIT WHERETO USE THE UNIT Keep at least 3.9. (10 cm) away from the wall. Approx. 57.9. (147 cm) Width approx. 27.5. (70 cm) Approx. 11.8. (30 cm) Mat Area where unit touches the floor Avoid places where the unit will be exposed to direct sunlight for long periods of time or places where it will be exposed to high temperatures, such as in front of a heater, etc., as this can cause discoloration or hardening of the leather. Placing a mat or cloth under the unit is recommended to prevent floor damage. The size of the mat should be sufficient [at least 42.1 in. . 27.5 in. (107 cm . 70 cm)] to cover the areas where the unit touches. Set the unit near the outlet. See Warning No. 11 and 12 on page 1. • • • 1 UNPACKTHE UNIT AND RAISE THE BACKREST CAUTION When raising the backrest, be careful not to cause hands or feet to become caught between the backrest and the backrest latch or the backrest and the armrests. Failure to follow this precaution may result in injury. • Check that there is nothing around the unit. Backrest latch 1 Remove the top of the shipping container. When packed for shipping the backrest is folded forward. 2 Remove the packing and cushioning materials and take out all accessories. 3 Raise the backrest. Do not connect the power cord to an electrical outlet during setup. Hold the backrest with both hands and lift in the direction of the arrow until it comes to a stop. Be careful the power cord and controller are not caught in the backrest. • • • • 2 INSPECT CONTENTS OF SHIPPING CONTAINER Massage Lounger Pillow Back Cushion Allen Key — 1 Attachment Screws — 8 Lock Switch Key — 1 The lock switch key has been inserted in the lock switch prior to leaving the factory. • Armrests — 2 English 3 HOWTO MOVE THE UNIT Using the wheels to move the unit Hold the backrest to move the unit when using the wheels. It is easier to move the unit with the massage heads retracted and the backrest in the upright position. *Place a mat or cloth on the floor and move the unit slowly to prevent floor damage. • • Lifting the Unit Move the unit by having 2 persons hold the armrests. *Please hold the armrests securely to avoid dropping the unit as it may damage your floor. • Move it slowly Wheels 4 INSTALL THE ARMRESTS ONTHE UNIT Front Back Left Velcro Zipper Convex Front Rear Round hole 1 Install the armrests. 1 Unfasten the velcro. 2 Unzip the zipper of the armrest completely. 3 Make sure to confirm the side (left or right) and direction (front or back) for each armrest. The illustration shows the left armrest. The right armrest is stamped “Front”, “Right” and “Back”. *The left armrest must be installed on the left hand side of the unit. 4 Align the proper armrest with the unit and connect. Be careful not to catch the fabric between the chair and the armrest. Lift up Secure with screws Allen key 2 Secure the armrests with attachment screws. (Total of 4 positions for a single armrest) Lift the fabric on the side of the armrest and insert the attachment screw onto the end of the Allen key, and then tighten. (Tighten the screws in the 4 positions lightly at first, and then tighten all screws firmly.) *If the screw does not enter into the hole, tighten the screw by pushing the armrest from the top. 3 Close the zipper at the bottom side of the armrests. When closing the zipper, be careful not to twist the end of the zipper. 1 Set the velcro. 2 Zip the zipper. 4 Put both ends of the zipper into the inside. 1 Turn in the edge of the zipper. 2 Fix the sliding tab of the zipper with the velcro. English 6ATTACHINGTHEBACKCUSHIONANDPILLOW1Attachthebackcushionusingthezipper. 5FIXTHECONTROLLERCORDApprox. 0. (51 cm) Usethecontrollercordvelcroestosecurethecord,leavingapproximately20in. (51cm)offreewire. * Confirm that there is a margin for the controller cord length when the backrest is reclined. (The illustration shows that the cord is attached to the right armrest.) 6ATTACHINGTHEBACKCUSHIONANDPILLOW1Attachthebackcushionusingthezipper. 5FIXTHECONTROLLERCORDApprox. 0. (51 cm) Usethecontrollercordvelcroestosecurethecord,leavingapproximately20in. (51cm)offreewire. * Confirm that there is a margin for the controller cord length when the backrest is reclined. (The illustration shows that the cord is attached to the right armrest.) 2Attachthepillowusingthevelcroes. FOLDINGTHEBACKRESTFORWARD(REPACKING) CAUTIONKeephands,feet,children,objects,etc.,clearofopeningsontheunit,includingseatandarmrests;gapsbetweentheunitandthefloor;andthebackrest’srangeofmovementwhenbeingfoldedforward. Failure to do so could result in injury. Theunitshouldnotbeturnedonandthecontrolsshouldnotbeoperatedonwhenthebackrestisfold...