Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
Have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors. Step 4-2: Connectors Introduction 1) ATX_12V 2) ATX 3) CPU_FAN 4) SYS_FAN 5) FDD 6) IDE1 / IDE2 7) F_PANEL 8) PWR_LED 9) RAM_LED 10) BATTERY 11) F_AUDIO 12) CD_IN 13) AUX_IN 14) SPDIF_IO 15) SUR_CEN 16) F_USB1 / F_USB2 17) CLR_CMOS 18) CI 2 5 8 3 1 6 9 13 4 18 7 11 14 12 15 16 10 17 8S661FXME-RZ Motherboard - 14 - English 1) ATX_12V (+12V Power Connector) This connector (ATX _12V) supplies the CPU operation voltage (Vcore). If this " ATX_ 12V connector" is not connected, system cannot boot. 2) ATX (ATX Power) AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to the mainboard. 20 1 11 10 Pin No. Definition 1 3.3V 2 3.3V 3 GND 4 +5V 5 GND 6 +5V 7 GND 8 Power Good 9 5V SB (stand by +5V) 10 +12V Pin No. Definition 11 3.3V 12 -12V 13 GND 14 PS_ON(soft on/off) 15 GND 16 GND 17 GND 18 -5V 19 +5V 20 +5V 3) CPU_FAN (CPU FAN Connector) A proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating. The CPU fan connector supports Max. current up to 600 mA. 1 2 4 1 3 Pin No. Definition 1 GND 2 +12V 3 Sense Pin No. Definition 1 GND 2 GND 3 +12V 4 +12V - 15 - Hardware Installation Process English 4) SYS_FAN (System Fan Connector) This connector allows you to link with the cooling fan on the system case to lower the system temperature. 5) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 360K,720K,1.2M,1.44M and 2.88Mbytes floppy disk types. The red stripe of the ribbon cable must be the same side with the Pin1. 6) IDE1 / IDE2 (IDE Connector) Please connect first harddisk to IDE1 and connect CDROM to IDE2. The red stripe of the ribbon cable must be the same side with the Pin1. IDE2 IDE1 1 39 2 40 1 34 2 33 1 Pin No. Definition 1 GND 2 +12V 3 Sense 8S661FXME-RZ Motherboard - 16 - English 7) F_PANEL (2x10 pins connector) Please connect the power LED, PC speaker, reset switch and power switch etc. of your chassis front panel to the F_PANEL connector according to the pin assignment above. 8) PWR_LED PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn to another color. 2 1 20 19 HDHD+ RES+ RESNC IDE Hard Disk Active LED Reset Switch SPEAKMSGMSG+ PWPW+ Message LED/ Power/ Sleep LED Power Switch Speaker Connector SPEAK+ 1 1 1 1 1 HD (IDE Hard Disk Active LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) SPEAK (Speaker Connector) Pin 1: VCC(+) Pin 2- Pin 3: NC Pin 4: Data(-) RES (Reset Switch) Open: Normal Operation Close: Reset Hardware System PW (Power Switch) Open: Normal Operation Close: Power On/Off MSG (Message LED/Power/ Pin 1: LED anode(+) Sleep LED) Pin 2: LED cathode(-) NC NC 1 Pin No. Definition 1 MPD+ 2 MPD- 3 MPD - 17 - Hardware Installation Process English 10) BATTERY 11) F_AUDIO (Front Audio Panel Connector) If you want to use Front Audio connector, you must remove 5-6, 9-10 Jumper. In order to utilize the front audio header, your chassis must have front audio connector. Also please make sure the pin assignments for the cable are the same as the pin assignments for the front audio header. To find out if the chassis you are buying support front audio connector, please contact your dealer. Please note, you can have the alternative of using front audio connector or of using rear audio connector to play sound. 9) RAM_LED Do not remove memory modules while RAM_LED is on. It might cause short or other unexpected damages due to the stand by voltage. Remove memory modules only when AC power cord is disconnected. + _ Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recom mended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. If you want to erase CMOS... 1. Turn off the computer and unplug the power cord. 2. Take out the battery gently and put it aside for about 10 minutes (Or you can use a metal object to connect the positive and negative pins in the battery holder to make them short for one minute). 3. Re-install the battery. 4. Plug the power cord and turn on the computer. 1 9 2 10 Pin No. Definition 1 MIC 2 GND 3 MIC_BIAS 4 Power 5 Front Audio(R) 6 Rear Audio(R)/Return R 7 NC 8 No Pin 9 Front Audio(L) 10 Rear Audio(L)/Return L 8S661FXME-RZ Motherboard - 18 - English 12/13) CD_IN (CD In Connector, black) / AUX_IN (AUX In Connector, white) Connect CD-ROM or DVD-ROM audio out to the connector. Connect other device (such as PCI TV Tunner audio out) to the connector. 14) SPDIF_IO (SPDIF In / Out Connector) The SPDIF output is capable of providing digital au...