Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
30.5 cm x 20 cm ATX Size form factor, 4 layers PCB. Motherboard . 6CX7 series includes 6CX7L, 6CX7, 6CX7-1 CPU . 100/133 MHz Pentiuma II/!!! Socket 370 Processor Intel Pentiuma!!! 100/133MHz FSB, Coppermine core FC-PGA . 2nd cache in CPU (Depend on CPU) Chipset . 82820 HOST / AGP / RDRAM Controller . 82801AA(ICH) I/O Controller Hub Clock Generator . Supports 100 / 133MHz . 105/110/117/120/125/127/135/137/140/145/150 MHz clocks (reserved) Memory . 2 184-pin RIMM Sockets I/O Control . Winbond W83627HF Slots . 1 AMR (Audio Modem Riser) slot . 1 Universal AGP slot (1X / 2X / 4X 1.5V/3.3V device support) . 5 32-bit Master PCI Bus slots (Note: If both of Creative CT5800 and Intel 82559 chipsets are on board, you have only 4 32-bit master PCI slots at PCI1~PCI4, PCI5 will be slave PCI slot) On-Board IDE . An IDE controller on the Intela 82801AA (ICH) PCI chipset provides IDE HDD/ CD-ROM with PIO, Bus Master (Ultra DMA33/ATA66) operation modes . Can connect up to four IDE devices On-Board Peripherals . 1 Floppy port supports 2 FDD with 360K, 720K, 1.2M, 1.44M and 2.88M bytes . 1 Parallel ports supports EPP/ECP mode . 2 Serial Ports (COM A & COM B) . 2 USB ports (Front USB is optional for NEC) . 1 IrDA connector for IR/CIR (Optional) Hardware Monitor . CPU/Power Supply/System Fan Revolution detect . CPU / Power / System Fan Control . System Voltage Detect . CPU Overheat Warning . Chassis Intrusion Detect . Display Actual Current Voltage PS/2 Connector . PS/2a Keyboard interface and PS/2a Mouse interface To be continued… 6CX7 Series Motherboard 6CX7 Series Motherboard Layout 6CX7 ICH 82801 MCH 82820Game & AudioCOM BCOM A LPT PS/2 BZ1 IDE1FLOPPY IDE2 AMR PCI1 AGP PCI 2 PCI 3 PCI4 PCI 5 Backup BIOS Main BIOS JP14 PGA 370 CPU RIMM 1USB LANRIMM 2 Creative CT5880 AOL*2 ASIC SW1JP8 BAT1 JP16 JP3 JP1 J1 JP18 JP15 J15 J7 J6 J8 J17 ATX Power JP6 JP5 JP11 Intel 82559 AC’97 JP24 JP20 J2 JP17 J10 JP4 JP9 JP10 J11 J12 J18 J14 JP21 JP27 JP28 CN9 J16 LED1 JP29 5 6CX7 Series Motherboard Layout 6 $ Page Index for CPU Speed Setup/Connectors/Panel and Jumper Definition Page CPU Speed Setup P.8 Connectors P.9 Game & Audio Port P.9 COM A / COM B / LPT Port P.9 USB & LAN Connector (LAN is optional) P.10 PS/2 Keyboard & PS/2 Mouse Connector P.10 J1 (CPU Fan) P.11 J17 (Power Fan) P.11 J16 (System Fan) P.12 ATX Power P.12 IR/CIR (Optional) P.13 Floppy Port P.13 IDE 1(Primary)/ IDE 2(Secondary) Port P.14 J8 (AUX_IN) P.14 J6 (CD Audio Line In) P.15 J7 (TEL) P.15 J2 (Wake On LAN) P.16 J10 (Ring Power On) P.16 J15 (External SMBUS Device Connector) P.17 JP15 (STR LED Connector) [Optional] & LED1 (RIMM LED) P.17 CN9 (FP USB)[For NEC] [Optional] P.18 J12 (Front Panel Jumper)[For NEC] P.18 J18 (AOL II Connector) [For NEC] [Optional] P.19 Panel and Jumper Definition P.20 J11 (2x11 Pins Jumper) P.20 JP16 (PS/2 Keyboard Power On) P.21 JP3 (Back USB device Wake Up Selection)[Optional] P.21 JP4 (Clear CMOS Function) [Optional] P.22 JP5 (Safe mode / Recovery / Normal) P.22 JP6 (Timeout Reboot Function) [Optional] P.23 JP11 (AMR Select)[Optional] P.23 JP17 (Case Open) P.24 JP20 (Onboard Sound Function Selection) P.24 JP21 (Front USB device Wake Up Selection)[Optional] P.25 JP27/JP28 (USB Port Selection) P.25 Connectors USB & LAN Connector (LAN is optional) 2 1 1 – Green LED (LAN Link LED) 2 – Yellow LED (LAN Active LED) 1 2 3 4 5 6 7 8 Pin No. Definition 1 USB V0 2 USB D03 USB D0+ 4 GND 5 USB V1 6 USB D17 USB D1+ 8 GND PS/2 Keyboard & PS/2 Mouse Connector PS/2 Mouse/ Keyboard Pin No. Definition 1 Data 2 NC 3 GND 4 VCC(+5V) 5 Clock 6 NC PS/2 Keyboard PS/2 Mouse 12 34 56 10 Connectors J16: System Fan ATX Power 1 Pin No. Definition 1 GND 2 +12V 3 SENSE 10 20 1 11 Pin No. Definition 3,5,7,13, 15-17 GND 1,2,11 3.3V 4,6,19,20 VCC 10 +12V 12 -12V 18 -5V 8 Power Good 9 14 5V SB stand by+5V PS-ON(Soft On/Off) 12 Connectors IDE1 (Primary), IDE2 (Secondary) Port IDE 2 IDE 1 Red Line J8: AUX_IN 1 Pin No. Definition 1 AUX-L 2 GND 3 GND 4 AUX-R 14 Connectors J2: Wake On LAN 1 Pin No. Definition 1 +5V SB 2 GND 3 Signal J10: Ring Power On 1 Pin No. Definition 1 Signal 2 GND 16 Connectors CN9: FP USB (For NEC)[Optional] 2 10 1 9 Pin No. Definition 1, 4,5,10 NC 2 Power 3, 7, 9 GND 6 USB D1+ 8 USB D1 J12: Front Panel Jumper (For NEC) 2 18 1 17 Pin No. Definition 1 HD LED+ 2 PWR LED+ 3 HD LED 4 GN LED+/STR LED+ 5,13, 8, 12 GND 6 PW 7 RST 9, 16 VCC 10 GN 11 IRRX 14, 17, 18 NC 15 IRTX 18 Suspend to RAM Installation A.3 How to put your system into STR mode? There are two ways to accomplish this: 1. Choose the “Stand by” item in the “Shut Down Windows” area. A. Press the “Start” button and then select “Shut Down” B. Choose the “Stand by” item and press “OK” 34 Suspend to RAM Installation C. Select the “Advanced” tab and “Standby” mode in Power Buttons. Step 4: Restart your computer to complete setup. Now when you want to enter STR sleep mode, just momentarily press the “Power on” button.. A.4 How to recover from the STR sleep mode? There are seven ways to “wake up” the system: 1....