Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
The system will halt and the following error message will appear in the mean time. You can run anti-virus program to locate the problem. Enabled Activate automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector or hard disk partition table. Disabled No warning message to appear when anything attempts to access the boot sector or hard disk partition table. (Default value) 47 BIOS Setup 48 • BIOS Flash Protection Enabled Enabled BIOS Flash Protection. Disabled Disabled BIOS Flash Protection. (Default Value) • Processor Number Feature This item will show up when you install the Pentium® !!! processor. Enabled Pentium® !!! Processor Number Feature. (Default value) Disabled Disabled this function. • First / Second / Third Boot device Floppy Select your boot device priority by Floppy. LS120 Select your boot device priority by LS120. ZIP Select your boot device priority by ZIP. HDD-0~3 Select your boot device priority by HDD-0~3. SCSI Select your boot device priority by SCSI. CDROM Select your boot device priority by CDROM. Disable Disable this function. LAN Select your boot device priority by LAN. • Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is 40 tracks 720 K, 1.2 M and 1.44 M are all 80 tracks. Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720 K, 1.2 M or 1.44 M drive type as they are all 80 tracks. (Default value) Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360 K. • Boot Up NumLock Status On Keypad is number keys. (Default value) Off Keypad is arrow keys. 6OX Motherboard • •••• Security Option This category allows you to limit access to the system and Setup, or just to Setup. System The system can not boot and can not access to Setup page will be denied if the correct password is not entered at the prompt. Setup The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt. (Default value) • •••• HDD S.M.A.R.T. Capability Enabled Enabled HDD S.M.A.R.T. Capability. Disabled Disabled HDD S.M.A.R.T. Capability. (Default value) • •••• Report No FDD For WIN 95 No Assign IRQ6 For FDD. (Default value) Yes FDD Detect IRQ6 Automatically. 49 BIOS Setup Advanced Chipset Features CMOS Setup Utility-Copyright( C ) 1984-2000 Award Software Advanced Chipset Features Top Performance Disabled SDRAM Timing Control Auto • SDRAM CAS Latency Time 3 .. SDRAM Cycle Time Tras/Trc 7/9 .. SDRAM RAS-to-CAS Delay 3 .. SDRAM RAS Precharge Time 3 Delayed Transaction Enabled AGP Graphics Aperture Size 64MB ..System Memory Frequency Auto SDRAM Buffer Strength Auto X SWE#, SCAS#, SRAS, SMAA, SBS Default X SMD[63:0], SDQM[7:0] Default X SMAA#[7:4] (Rows 0/1) Default X SMAB#[7:4] (Rows 2/3) Default X SMAC#[7:4] (Rows 4/5) Default X SCS[0]# (Row 0) Default X SCS[1]# (Row 1) Default X SCS[2]# (Row 2) Default X SCS[3]# (Row 3) Default X SCS[4]# (Row 4) Default X SCS[5]# (Row 5) Default X SCKE[0]# (Row 0) Default X SCKE[1]# (Row 1) Default X SCKE[2]# (Row 2) Default X SCKE[3]# (Row 3) Default X SCKE[4]# (Row 4) Default X SCKE[5]# (Row 5) Default Item Help Menu Level ^v> <:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5:Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults Figure 4: Advanced Chipset Features .. These four items will be available when ”SDRAM Timing Control” is set to Manual. .. This option will not be available when FSB DIP switch is present. 50 6OX Motherboard • •••• Top Performance If you wish to maximize the performance of your system, set “Top Performance” as “Enabled”. Disabled Disabled this function. (Default Value) Enabled Enabled Top Performance function. • •••• SDRAM Timing Control Auto Set SDRAM Timing Control to Auto. (Default value) Manual Set SDRAM Timing Control to Manual. • •••• SDRAM CAS latency Time 3 For Slower SDRAM DIMM module. (Default Value) 2 For Fastest SDRAM DIMM module. • •••• SDRAM Cycle Time Tras/Trc 7/9 Set SDRAM Tras/Trc Cycle time to 7/9 SCLKs. (Default value) 5/7 Set SDRAM Tras/Trc Cycle time to 5/7 SCLKs. • •••• SDRAM RAS-to-CAS delay 3 Set SDRAM RAS-to-CAS delay 3 SCLKs. (Default value) 2 Set SDRAM RAS-to-CAS delay 2 SCLKs. • •••• SDRAM RAS Precharge Time 3 Set SDRAM RAS Precharge Time to 3. (Default value) 2 Set SDRAM RAS Precharge Time to 2. • •••• Delayed Transaction Disabled Normal operation. Enabled For slow speed ISA device in system. (Default value) • •••• AGP Graphics Aperture Size 32 MB AGP Graphics Aperture Size is 32MB. 64 MB AGP Graphics Aperture Size is 64MB. (Default Value) 51 BIOS Setup 52 • System Memory Frequency Auto Set System Memory Frequency to Auto. (Default value) 100MHz Set System Memory Frequency to 100MHz. 133MHz Set System Memory Frequency to 133MHz. • SDRAM Buffer Strength Auto Set SDR...