Évaluations - 0, GPA: 0
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Auto BIOS will automatically adjust the HT Link Width. (Default) 8 bit Sets HT Link Width to 8 bit. 16 bit Sets HT Link Width to 16 bit. HT Link Frequency Allows you to manually set the frequency for the HT Link between the CPU and chipset. Auto BIOS will automatically adjust the HT Link Frequency. (Default) x1~x10 Sets HT Link Frequency to x1~x10 (200 MHz~2.0 GHz). Set Memory Clock Determines whether to manually set the memory clock. Auto lets BIOS automatically set the memory clock as required. Manual allows the memory clock control item below to be configurable. (Default: Auto) Memory Clock This option is configurable only when Set Memory Clock is set to Manual. X4.00 Sets Memory Clock to X4.00. X5.33 Sets Memory Clock to X5.33. X6.66 Sets Memory Clock to X6.66. X8.00 Sets Memory Clock to X8.00. DRAM Configuration CMOS Setup Utility-Copyright (C) 1984-2010 Award Software DRAM Configuration Item Help Menu Level . CPU Host Clock Control [Auto] x CPU Frequency(MHz) 200 Set Memory Clock [Auto] x Memory Clock x6.66 1333Mhz DCTs Mode [Unganged] DDR3 Timing Items [Auto] SPD Auto x CAS# latency Auto 7T 7T x RAS to CAS R/W Delay Auto 7T 7T x Row Precharge Time Auto 7T 7T x Minimum RAS Active Time Auto 30T 30T x 1T/2T Command Timing Auto -- -- x TwTr Command Delay Auto 5T 5T x Trfc0 for DIMM1 Auto 90ns 90ns x Trfc2 for DIMM2 Auto -- -- x Trfc1 for DIMM3 Auto -- -- x Trfc3 for DIMM4 Auto -- -- x Write Recovery Time Auto 10T 10T x Precharge Time Auto 5T 5T x Row Cycle Time Auto 28T 28T ....: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2010 Award Software DRAM Configuration Item Help Menu Level . x RAS to RAS Delay Auto 4T 4T **DCTs Drive Strength** DCT0 DCT1 ProcOdt(ohms) [Auto] 60 [Auto] 240 DQS Drive Strength [Auto] 1.0x [Auto] 1.5x Data Drive Strength [Auto] 1.0x [Auto] 1.5x MEMCLK Drive Strength [Auto] 1.5x [Auto] 1.5x Addr/Cmd Drive Strength [Auto] 1.5x [Auto] 2.0x CS/ODT Drive Strength [Auto] 1.5x [Auto] 2.0x CKE Drive Strength [Auto] 1.5x [Auto] 2.0x Bank Interleaving [Enabled] Channel interleave [Enabled] DQS Training Control [Skip DQS] CKE Power Down Mode [Disabled] Memclock tri-stating [Disabled] ....: Move Enter: Select +/-/PU/PD: Value F10: Save ESC: Exit F1: General Help F5: Previous Values F6: Fail-Safe Defaults F7: Optimized Defaults CPU Host Clock Control, CPU Frequency (MHz), Set Memory Clock, Memory Clock The settings under the four items above are synchronous to those under the same items on the MB Intelligent Tweaker(M.I.T.) main menu. DCTs Mode Allows you to set memory control mode. Ganged Sets memory control mode to single dual-channel. Unganged Sets memory control mode to two single-channel. (Default) DDR3 Timing Items Manual allows all DDR3 Timing items below to be configurable. Options are: Auto (default), Manual. CAS# latency Options are: Auto (default), 4T~12T. RAS to CAS R/W Delay Options are: Auto (default), 5T~12T. Row Precharge Time Options are: Auto (default), 5T~12T. Minimum RAS Active Time Options are: Auto (default), 15T~30T. 1T/2T Command Timing Options are: Auto (default), 1T, 2T. TwTr Command Delay Options are: Auto (default), 4T~7T. Trfc0 for DIMM1 Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Trfc2 for DIMM2 Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Trfc1 for DIMM3 Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Trfc3 for DIMM4 Options are: Auto (default), 90ns, 110ns, 160ns, 300ns, 350ns. Write Recovery Time Options are: Auto (default), 5T~8T, 10T, 12T. Precharge Time Options are: Auto (default), 4T~7T. Row Cycle Time Options are: Auto (default), 11T~42T. RAS to RAS Delay Options are: Auto (default), 4T~7T. **DCTs Addr/Cmd Timing** ProcOdt(ohms) Options are: Auto (default), 240 ohms, 120 ohms, 60 ohms. DQS Drive Strength Options are: Auto (default), 0.75x, 1.0x, 1.25x, 1.5x. Data Drive Strength Options are: Auto (default), 0.75x, 1.0x, 1.25x, 1.5x. MEMCLK Drive Strength Options are: Auto (default), 0.75x, 1.0x, 1.25x, 1.5x. Addr/Cmd Drive Strength Options are: Auto (default), 1.0x, 1.25x, 1.5x, 2.0x. CS/ODT Drive Strength Options are: Auto (default), 1.0x, 1.25x, 1.5x, 2.0x. CKE Drive Strength Options are: Auto (default), 1.0x, 1.25x, 1.5x, 2.0x. Bank Interleaving Enables or disables memory bank interleaving. Enabled allows the system to simultaneously access different banks of the memory to increase memory performance and stability. (Default: Enabled) Channel interleave Enables or disables memory channel interleaving. Enabled allows the system to simultaneously access different channels of the memory to increase memory performance and stability. (Default: Enabled) DQS Training Control Enables or disables memory DQS training each time the system restarts. (Default: Skip DQS) CKE Power Down Mode Determines whether to set the memory to power down mode when the CKE pin is closed. (Default: Disabl...