Évaluations - 0, GPA: 0 ( )

Fabricant : Gigabyte Taille : 27.04 mb Nom Fichier : Langue d'enseignement:

Par ce dispositif a également d'autres instructions :

Carte mère - GA-H77-DS3H (28.53 mb)

Carte mère - GA-H77-DS3H (28.32 mb)

Carte mère - GA-H77-DS3H (27.41 mb)

Restart your system after the driver installation. Figure 2 Figure 1 C. Configuring EZ Smart Connect Select Config (Figure 3) and add new programs to the White Program list (Note ) (Figure 4). Then click OK and restart the system. Figure 4 Figure 3 D. Disabling EZ Smart Connect To disable EZ Smart Connect, select Disable EZ Smart Connect and click Setup. (Note) This feature works best with programs designed to work automatically with the Internet to obtain their data such as Microsoft Outlook®, Microsoft Windows Live™ Mail, and Seesmic®. Unique Features - 75 - Appendix Chapter 5 Appendix 5-1 Configuring SATA Hard Drive(s) RAID Levels RAID 0 RAID 1 RAID 5 RAID 10 Minimum Number of Hard Drives .2 2 .3 .4 Array Capacity Number of hard drives * Size of the smallest drive Size of the smallest drive (Number of hard drives -1) * Size of the smallest drive (Number of hard drives/2) * Size of the smallest drive Fault Tolerance No Yes Yes Yes To configure SATA hard drive(s), follow the steps below: A. Install SATA hard drive(s) in your computer. B. Configure SATA controller mode in BIOS Setup. C. Configure a RAID array in RAID BIOS. (Note 1) D. Install the SATA RAID/AHCI driver and operating system. (Note 2) Before you begin Please prepare: ••At least two SATA hard drives (to ensure optimal performance, it is recommended that you use two hard drives with identical model and capacity). If you do not want to create RAID, you may prepare only one hard drive. ••Windows 7/XP setup disk. ••Motherboard driver disk. ••A USB floppy disk drive (needed during Windows XP installation) ••An empty formatted floppy disk (needed during Windows XP installation) 5-1-1 Configuring SATA Controllers A. Installing SATA hard drive(s) in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port(Note 3) on the motherboard. Then connect the power connector from your power supply to the hard drive. (Note 1) Skip this step if you do not want to create RAID array on the SATA controller. (Note 2) Required when the SATA controller is set to AHCI or RAID mode. (Note 3) When a RAID set is built across the SATA 6Gb/s and SATA 3Gb/s channels, the system performance of the RAID set may vary depending on the devices being connected. Appendix - 76 - B. Configuring SATA controller mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup. Step 1: Turn on your computer and press to enter BIOS Setup during the POST (Power-On Self-Test). To create RAID, set SATA Mode Selection under the Peripherals menu to RAID (Figure 1). If you do not want to create RAID, set this item to IDE or AHCI. (IDE by default) Figure 1 Step 2: Save changes and exit BIOS Setup. The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. Appendix C. Configuring a RAID array in RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array. Skip this step and proceed with the installation of Windows operating system for a non-RAID configuration. Step 1: After the POST memory test begins and before the operating system boot begins, look for a message which says "Press to enter Configuration Utility" (Figure 2). Press + to enter the RAID Configuration Utility. Intel(R) Rapid Storage Technology - Option ROM - 11.0.0.1339 Copyright(C) 2003-11 Intel Corporation. All Rights Reserved. RAID Volumes : None defined. Physical Devices : ID Device Model Serial # Size Type/Status(Vol ID) 0 ST3120026AS 3JT354CP 111.7GB Non-RAID Disk 1 ST3120026AS 3JT329JX 111.7GB Non-RAID Disk Press to enter Configuration Utility.. Figure 2 Step 2: After you press + , the MAIN MENU screen will appear (Figure 3). Create RAID Volume If you want to create a RAID array, select Create RAID Volume in MAIN MENU and press . Intel(R) Rapid Storage Technology - Option ROM - 11.0.0.1339 Copyright(C) 2003-11 Intel Corporation. All Rights Reserved. [ MAIN MENU ] 4. Recovery Volume Options 5. Acceleration Options 6. Exit 1. Create RAID Volume 2. Delete RAID Volume 3. Reset Disks to Non-RAID [ DISK/VOLUME INFORMATION ] RAID Volumes : None defined. Physical Deivces : ID Device Model Serial # Size Type/Status(Vol ID) 0 ST3120026AS 3JT354CP 111.7GB Non-RAID Disk 1 ST3120026AS 3JT329JX 111.7GB Non-RAID Disk [hi]-Select [ESC]-Exit [ENTER]-Select Menu Figure 3 Appendix Step 3: After entering the CREATE VOLUME MENU screen, enter a volume name with 1~16 letters (letters cannot be special characters) under the Name item and press . Then, select a RAID level (Figure 4). RAID levels supported include RAID 0, RAID 1, RAID 10, and RAID 5 (the selections available depend on the number of the hard drives being installed). Press to proceed. Intel(R) Rapid Storage Technology - Option ROM - 11.0.0.1339 Copyri...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :