Évaluations - , GPA: ( )

Instructions Alvin, Modèle Parallel Straightedge 2201

Fabricant : Alvin
Taille : 1.17 mb
Nom Fichier : f3f6d7cc-a0ac-4eef-ac72-9d3a3bcd88ec.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

2. Check that drawing board has a solid outer frame to hold screws and that it is not warped. Alvin straightedges will not work properly on warped boards. 3. Position front and rear wire connectors on top of drawing board as shown in Figure 1. Use chart below to determine proper spacing. Center the straightedge on the board. For Straightedge Length Dimension A Dimension B Dimension C 30" 27." 28." ." 36" 33." 34." ." 42" 39." 40." ." 48" 45." 46." ." 60" 57." 58." ." Proceed to step 4 on next page. Tools Required: Phillips screwdriver and 1.16" drill or awl Straightedge with Wire and Spring (1) Front Wire Connectors (2) Right Rear Wire Connector (1) Left Rear Wire Connector (1) Rear Pulleys (2) Rear Brake Knob (1) 1/2" Brake Stud Screw (1) 3/4" Screws* (6) 5/8" Screws* (2) 3/8" Washers (2) To assemble, follow step-by-step instructions below: wire *NOTE: Only six screws total are required for installation. We have included two extra screws to accomodate various board thicknesses. Parts List Figure 2 Figure 3 Figure 4 ." Screw ." Screw* ." Screw ." Brake Stud Screw ." Screws* 4. Mark screw positions for front and rearconnectors and pre-drill pilot holes about ." deepusing a 1.16" drill bit. TIP: Wrap maskingtape ." from drill tip to set drilling depth. Use care not to drill through tabletop. 5. Fasten front connectors to front edge of boardas shown in Figure 2 using ." screws. Fastenscrews half way. Do not fully tighten. 6. Assemble right rear connector as shown in Figure 3and fasten to board. Select screw length based uponboard thickness.* Fasten screws securely. *For board thicknesses of 5/8" or less: If your board is 5.8" thick or less please use the5.8" screws in place of the ." screws as shown inFigures 3 and 4. Do not use ." screws included with hardware kit since they might break throughbottom of board. Front connector 3.8" Washer Pulley Post Right RearConnector Rear Brake Knob ." Screws* * Use the 5.8" screws in placeof the ."screws for boards 5.8" thick or less. Figure 2 Figure 3 Figure 4 ." Screw ." Screw* ." Screw ." Brake Stud Screw ." Screws* 4. Mark screw positions for front and rearconnectors and pre-drill pilot holes about ." deepusing a 1.16" drill bit. TIP: Wrap maskingtape ." from drill tip to set drilling depth. Use care not to drill through tabletop. 5. Fasten front connectors to front edge of boardas shown in Figure 2 using ." screws. Fastenscrews half way. Do not fully tighten. 6. Assemble right rear connector as shown in Figure 3and fasten to board. Select screw length based uponboard thickness.* Fasten screws securely. *For board thicknesses of 5/8" or less: If your board is 5.8" thick or less please use the5.8" screws in place of the ." screws as shown inFigures 3 and 4. Do not use ." screws included with hardware kit since they might break throughbottom of board. Front connector 3.8" Washer Pulley Post Right RearConnector Rear Brake Knob ." Screws* * Use the 5.8" screws in placeof the ."screws for boards 5.8" thick or less. 7. Assemble left rear connector as shown in Left Rear Figure 4 and fasten to board. Fasten screws Connector securely. Pulleys are designed to be tight fitting and do not spin freely. 8. Place straightedge in center of drawing boardparallel to front edge as shown in Figure 5. 9. Loop upper wires around pulleys in rear wireconnectors making sure that spring is centered. 10. Thread lower left and lower right wires throughfront wire connectors. Wire should passbetween connector and board as shown in Figure 6. 11. With spring still centered at top, pull slack outof wire passing through lower left connectorand wrap wire around mounting screw. Fastenscrew securely. 12. Pull slack out of wire passing through lower rightconnector until spring at top is stretched to about2." in length. Wrap wire around mounting screwand fasten screw securely. Use care to set springtension as directed for best performance...