! ! WARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. Read the Installation, Operating and Maintenance Instructions thoroughly before installing or servicing this equipment. ! This equipment has been engineered to provide you with year round dependable service when used according to the instructions in this manual and standard commercial kitchen practices. P/. 78009. 3/0. Phone: +1 (214) 421-7366 Fax: +1 (214) 565-0976 Toll

If replacement parts are ever required, only use parts that have been approved by the manufacturer. WARRANTY INFORMATION See Warranty on page 11. To determine if your cabinet is still covered by warranty, telephone the BevLes Manufacturing Facility at (800) 441-1601. Give them the serial and model numbers which are located on the product identification plate at the right end of the control module. 4 606.00.01111 28.085 23.135 2.181 22.7.67969 28.085 23.135 2.181 14.982 5.806 1.355 2525.9.91177 1

Read the Installation, Operating and Maintenance Instructions thoroughly before installing or servicing this equipment. This equipment has been engineered to provide you with year round dependable service when used according to the instructions in this manual and standard commercial kitchen practices. P.’N 780084 5,'08 Phone. +1 (214)421-7366 Fax: +1 (214)565-0976 Toll Free: +1 (800)441-1601 BevLes Website: 729 Third Avenue E-mail: sales@BevLes.com Dallas, TX 75226 The BevLes Company tak

(Fig. 41) 4. Mark all the wires connected to the fan blower motor(s) with a color code or number to make proper re-connection easy. (Fig. 42) 5. Remove wire nuts and set cover aside. 6. For CA70 units, remove the two screws securing the clips that attach the copper thermostat probe to the fan blower. Use a medium flathead screwdriver. Free the copper probe and carefully set out of the way. (Fig. 43) **NOTE: DO NOT kink or bend copper tubing or probe. Remove four screws (two at each end) that hol

phillip. 15 82024 Blower Motor 16 70173 Mounting, Screw #10-24 x .” s/. phillip. 17 70144 Lockwasher, #10 s/s internal tooth 18 70141 Nut, #10-24 hex s/s 19 41068 Motor Cover 20 41072 Air Duct Cover 37 41072 Motor Housing Cover 37A 41136 Motor Housing Cover, MP 38 41172 Air Flow Cover Extension, MP 7-6l. Heating Element Parts List (CA43 Mdls) Dwg 7-5c Ref # DescriptionPart Number 22 82124 Heating Element, 1500W. 120. 22A 82296 Heating Element, 1800W. 120. (M. o. H. Mdls. 23 41044 Front Clip, 0.8

Water Pan Baffle,22ga7”x8.5" Door Gasket, magnetic 21.5" x 57" Door Gasket, magnetic 26" x 57”, MP Gasket Retainer, top. outer 22.37” Gasket Retainer, top outer 26.87", MP Gasket Retainer, bottom outer 22.37” Gasket Retainer, bottom outer 26.87”, M. Gasket Retainer, side outer 58.37” Sheet Metal Screw, #6 x 3/4" hex head Caster, 5” with brake Caster, 5” without brake Nut, hex 5/16"-18 Lockwasher, 5/16" internal tooth Bolt, hex 5/16"-18 x 1 1/4” Air Duct Assembly, upper (CV16) Air Duct Assembly,

Remove thermostat dial from front panel by rotating the dial to expose the set screw and reversing the sat screw with a small flathead screwdriver. (Fig. 34) 4. Remove the two screws holding the bezel (chrome ring) behind the thermostat dial with a medium (6”) phillips screwdriver. Carefully pull thermostat away from the rear of the front cover. 5. Remove the fan blower motor assembly cover (on the left side of module as you are facing the front panel) by removing the two front and two rear scre

. 1/4. rd. hd. s/. phillips Mounting Screw, 11 82136 Knob, thermostat 50-250°F 12 70284 Socket Set Screw, Thermosta. Kno. #8-3. 13 83112 Clamp, Thermostat Probe 14 82082 Power Switch, LTIGK-6S-WH-NBL 15 82024 Blower Motor 16 70173 s/. phillips Mounting Screw, #10-24 x 1/2” 17 70144 Lockwasher, #10 s/s internal tooth 18 70141 Nut, #10-24 hex s/s 20 41068 Motor Air Duct Cover 21 41052 Water Pan Slide 22 82124 1500W. 120. Heating Element, 22A 82296 Heating Element, 1800W. 120. (M. o. H. Mdls. 23 41

Tighten screws to secure power cord into connector. *"WARNING: Replace only with a BEVLES power cord properly rated for your unit. 8. Insert new wires through opening in back panel and reattach elbow connector. 9. Reattach green ground wire to back panel. 10. Reconnect power cord wires using wire nuts and wiring diagram. Retape over wire nuts and wires. (Diagram 3) **WARNING: Severe damage can be caused to your unit by improperly connecting wires. 11. Replace the back panel using the five philli

hd. s/. phillip. 9 Machine Screw, 1/4"-20 x .” phillips 11 Knob, thermostat 50-250°F 10 Latch 12 Socket Set Screw, Thermostat Knob #8-32 11 Latch Strike 13 Clamp, Thermostat Probe 12 Latch Pin, 5/16" x 8.5" rod 14 Power Switch, LTlGK-6S-WH-NBL 13 Latch Spring #CDL5019 15 Blower Motor 17 Air Duct Assembly (CV13) 16 Mounting Screw, #10-24 x 1/2" s/s phillips 19 Button, aluminum #l0-23-75R 17 Lockwasher, #10 S/S internal tooth 20 Sheet Metal Screw, T/H #8 x 1/4” phillips 18 Nut, #10-24 hex s/s 21 W