Évaluations - , GPA: ( )

Instructions Broan, Modèle EVOLUTION QP236SS

Fabricant : Broan
Taille : 2.14 mb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitions and elbows. Page 3 (D Use the proper diagram below, for placement of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole. HOOD MOUNTING SCREWS (5) I 11 V (30" hood) 11%' -14 5/8" (36" hood) —«-14 5/8' 17 V (42" hood) 17 %' {-CABINET FRONT 3%” X 10” VERTICAL DUCTING CABINET BOTTOM ■5%" (30" hood) (36" hood) ■ (42" hood) 67/s' 7T -5%" VERTICAL DUCT ACCESS HOLE 11' & a 1078" 2%" ‘WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL ACCESS HOLE (in cabinet bottom) WOOD SHIMS (recessed-bottom cabinets only) 3%” X 10” HORIZONTAL DUCTING CABINET FRONT 13/8" r 4" CABINET ± BOTTOM HORIZONTAL DUCT ACCESS HOLE -5%'- 11 5/8" (30" hood) ■14 %" (36" hood)-17 %" (42" hood) HOOD MOUNTING SCREWS (5) -5%- ■ 67/8' 11 5/8" (30" hood) -14 %" (36" hood) 17 %" (42" hood) CENTER LINE ELECTRICAL ACCESS HOLE (in wall) HOOD MOUNTING SCREWS (5) 11 V (30" hood) 11 V (30" hood) -14 V (36" hood)-' " 17 V (42" hood) f CABINET FRONT 7-IN. ROUND DUCTING -14 V (36" hood)-17 V (42" hood) 107/8" WOOD SHIMS (recessed-bottom cabinets only) CENTER LINE ELECTRICAL ACCESS HOLE (in cabinet bottom) 2 * Note the extra wood shim and mounting screw near the cabinet front, on the cabinet center line. BR6AN MODELS QP230BC • QP230BL • QP230SS • QP230WW QP236BC • QP236BL • QP236SS • QP236WW QP242BC • QP242BL • QP242SS • QP242WW PREPARE THE HOOD |~3~| Remove parts bag from inside the foam packaging end cap. |~4~| Remove all protective polyfilm from the hood (stainless steel hoods only). [~5~| Remove the Aluminum Filters from the hood. Page 4 7 | Remove 2 Screws holding Damper / Duct Connector to hood. Remove damper/duct connector from inside the hood. FOR DUCTED INSTALLATIONS - Skip to Step 12. |~8~| NON-DUCTED INSTALLATION ONLY: From parts bag: Attach Non-Duct Diverter to Air Box with 2 Screws and 2 Washers. |~9~| NON-DUCTED INSTALLATION ONLY: Remove 2 Screws holding Non-Duct Plate to Non-Duct Plenum and remove plate. [ÏÏÏ] NON-DUCTED INSTALLATION ONLY: Insert short end of Non-Duct Plate into Non-Duct Plenum Slot. Attach with 2 Screws removed in Step 9. [ïï~| NON-DUCTED INSTALLATION ONLY: Purchase a set of (2) non-ducted filters for 30” wide hoods (Model BPPF30) & 36” wide hoods (Model BPPF36) or a set of (3) non-ducted filters for 42” wide hoods (Model BPPF42) from your local distributor or retailer. Attach the non-ducted filters to the aluminum mesh filters following instructions packed with the non-ducted filters. FOR NON-DUCTED INSTALLATIONS - Skip to “INSTALL THE HOOD" BROAN MDLS [T2~ DUCTED INSTALLATION ONLY: Remove 3%” x 10 vertical, 3%” x 10” horizontal, or 7-inch round knockout plate(s) as appropriate for your ducting method. R3J DUCTED INSTALLATION ONLY: Attach 314” x 10” Damper/...