Log:
Téléchargements : 10   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings. 2. Always turn hood ON when cooking at high heat or when cooking flaming foods (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé). 3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter. 4. Use proper pan size. Always use cookware appropriate for the size of the surface element. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT

Téléchargements : 4   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

If the fuse has opened (blown), the green fan setting or light setting indicators will not operate properly when the fan or light buttons are pressed, and the fan and lights will not turn on. A new fuse can be purchased at your local electronic supply store. Use an 8A, 120V, 5 mm diameter, 20 mm long, fast-acting, cartridge-type fuse. To replace the fuse: 1. Disconnect power at service entrance. 2. Remove filters and bottom pan. 3. Remove and inspect fuse. If it is not open (blown), additio

Téléchargements : 4   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

Remove damper/duct connector from inside the hood. FOR DUCTED INSTALLATIONS - Skip to Step 12. |~8~| NON-DUCTED INSTALLATION ONLY: From parts bag: Attach Non-Duct Diverter to Air Box with 2 Screws and 2 Washers. |~9~| NON-DUCTED INSTALLATION ONLY: Remove 2 Screws holding Non-Duct Plate to Non-Duct Plenum and remove plate. [ÏÏÏ] NON-DUCTED INSTALLATION ONLY: Insert short end of Non-Duct Plate into Non-Duct Plenum Slot. Attach with 2 Screws removed in Step 9. [ïï~| NON-DUCTED INSTALLATION

Téléchargements : 9   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state. This warranty supersedes all prior warranties. To qualify for warranty service, you must (a) notify Broan-NuTone at the address or telephone number below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. At the time of requesting warranty service, you must present evidence of the original purchase date. Broan-NuTone

Téléchargements : 8   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

- not by KEY NO. 99527290C BR6ÄN MODELES QP230BC • QP230BL • QP230SS • QP230WW QP236BC • QP236BL • QP236SS • QP236WW QP242BC • QP242BL • QP242SS • QP242WW EVOLUTION™ 2 Hottes de cuisine de série QP2 Page 8 LIRE CES DIRECTIVES ET LES CONSERVER A POUR USAGE DOMESTIQUE SEULEMENT A A A AVERTISSEMENT A A AVERTISSEMENT AFIN DE DIMINUER LES RISQUES D’INCENDIE, D’ELECTRO- CUTION OU DE BLESSURES, SUIVEZ CES DIRECTIVES : 1. N’utilisez cet appareil que de la manière prévue par le fabricant. Si

Téléchargements : 3   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

Turns light on to MEDIUM setting. Turns light on to HIGH setting. » CO 8 tv FAN (3 pushbutton switches) Turns fan on to LOW speed. Turns fan on to MEDIUM speed. Turns fan on to HIGH speed. Pressing the same fan button again will turn fan OFF. A light above each button indicates fan speed. NOTE This hood utilizes an offset blower design to achieve greater performance and lower sound levels. As a result, you may notice that cooking impurities are more attracted to one side or appear to b

Téléchargements : 8   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

For vertical or horizontal discharge, run ductwork between the hood location and a roof cap or wall cap. For best results, use a minimum number of transitions and elbows. Page 3 (D Use the proper diagram below, for placement of ductwork and electrical cutout in cabinet or wall. For a non-ducted installation, DO NOT cut a duct access hole. HOOD MOUNTING SCREWS (5) I 11 V (30" hood) 11%' -14 5/8" (36" hood) —«-14 5/8' 17 V (42" hood) 17 %' {-CABINET FRONT 3%” X 10” VERTICAL DUCTING CABINET

Téléchargements : 6   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

as the blower motor will shut down intermittantly. 5. Your hood motor has a thermal overload which will automatically shut off the motor if it becomes overheated. The motor will restart when it cools down. If the motor continues to shut off and restart, have the hood serviced. 6. The top of the hood MUST NOT BE LESS than 24” and at a maximum of 30” above cooktop for best capture of cooking impurities. 7. This hood is not intended to be used as a shelf. 8. Please read specification label on p

Téléchargements : 3   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

Attach the non-ducted filters to the aluminum mesh filters following instructions packed with the non-ducted filters. FOR NON-DUCTED INSTALLATIONS - Skip to “INSTALL THE HOOD" BROAN MDLS [T2~ DUCTED INSTALLATION ONLY: Remove 3%” x 10 vertical, 3%” x 10” horizontal, or 7-inch round knockout plate(s) as appropriate for your ducting method. R3J DUCTED INSTALLATION ONLY: Attach 314” x 10” Damper/Duct Connector (if using 3%” x 10” duct) or 7” Round Duct Plate (if using 7-inch round duct) over t

Téléchargements : 1   Taille : 2 mb   Fabricant : Broan  
Catégorie : fours à micro-ondes
@name@name@name

HD. MOUNTING SCREWS (2) #8 X 5/16” MACHINE SCREWS & (2) #8 WASHERS FOR NON-DUCT DIVERTER CLEANING & MAINTENANCE For performance, appearance, and health reasons, clean filter, fan and grease-laden surfaces. Use only a clean cloth and mild detergent solution on stainless and painted surfaces. Clean all-metal filters in the dishwasher using a non-phosphate detergent. Discoloration of the filter may occur if using phosphate detergents, or as a result of local water conditions - but this will





catégories