Évaluations - 3, GPA: 3.3
(
)
)
|
Facilité d'utilisation
Close Wire Cage Assembly. Select Low speed. To begin mixing, press and hold the Start button; then raise the bowl. – 10 – Bowl Guard (Fig. 5) The Wire Cage Assembly on the Bowl Guard can be rotated out-of-the-way to add ingredients or access the bowl and agitator. To rotate the Wire Cage Assembly to the rear . . . Push the Latch in to release the Centering Pin from the Centering Ramp. Note how the grooves on the nylon Retainers allow the Wire Cage to ride around the circular Ridge of the planetary Drip Cup. The Wire Cage can rotate 360°; left or right. When the Wire Cage returns to the front and center position, the Centering Pin is captured and held by the Centering Ramp, restricting rotation of the Wire Cage until the Latch is pressed again. The Wire Cage must be in the front-center position for the mixer to operate. To remove the Wire Cage Assembly for cleaning . . . Lower the Bowl. Rotate the Wire Cage to the rear. Remove both Agitator and Bowl. Return the Wire Cage to the front. While holding the Wire Cage securely with both hands, use your thumb to push down on the Black Release Knob. Lower and remove the Wire Cage. Wash it in a sink or dishwasher; rinse with clear water; and dry with a clean cloth. The stainless steel Splash Guard can be wiped-off or washed easily with a cloth or sponge and warm soapy water. Rinse with clear water. Dry with a clean cloth. To reinstall the Wire Cage Assembly . . . Hold the Wire Cage so its top ring is positioned around the planetary Drip Cup with the grooves in both nylon Rear Retainers straddling the Ridge on the Drip Cup. Push-in the Front-Center Retainer until it stays in and so that its grooves also straddle the Ridge on the Drip Cup. The Wire Cage is properly assembled when all three Retainers straddle the Ridge on the Drip Cup in the three opposed locations. Rotate the Wire Cage out-of-the-way to install or remove the Agitator and Bowl or to add ingredients. Return the Wire Cage to its front and center position to operate the mixer. Wire Cage Rotated Left Latch Ridge On Drip Cup Rear Retainer Splash Guard Front-Center Centering Ramp Retainer Wire Cage Front-Center Position Centering Pin Black Release Knob PL-40071-1 Fig. 5 – 11 – Attachments To install an attachment, loosen the attachment hub thumb screw and remove the plug. Insert the attachment into the attachment hub, making certain that the square shank of the attachment is in the square driver of the mixer. Secure the attachment by tightening the thumb screw. Move the gear shift lever to the desired speed. With the bowl support all the way up and the wire cage in the front-center position, start the mixer to operate the attachment. The meat and food chopper attachment should be operated in second or third speed. If material in the cylinder stalls the mixer, push the STOP button at once. DO NOT attempt to restart the mixer in a lower speed — remove the adjusting ring, knife, plate, and worm and clear any obstruction. THIS ATTACHMENT MUST NOT BE USED TO CHOP BREAD CRUMBS. NOTE: Attachment hub should not be used while mixing. Mixer Speeds Speed 1 (Low) — This speed is for heavy mixtures such as pizza dough, heavy batters, and potatoes. Speed 2 (Medium-low) — This speed is for mixing cake batters, mashing potatoes, and developing bread dough. Speed 3 (Medium-high) — This speed is for incorporating air into light batches, as well as finishing whipped items. Speed 4 (High) — This speed is for maximum and accelerated air incorporation into light batches. Bowl Scraper Attachment The Mixer Bowl Scraper Attachment (when ordered) is provided with a separate instruction manual covering its installation, operation, use and care. CLEANING WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT BEFORE BEGINNING ANY CLEANING PROCEDURE. A flat scraper and a brush are furnished to aid in cleaning bowls and agitators. The mixer should be thoroughly cleaned daily. DO NOT use a hose to clean the mixer — it should be washed with a clean damp cloth. The base allows ample room for cleaning under the mixer. The apron may be removed by loosening the thumb screws. Behind this apron is an access cover which may be removed for cleaning. The Drip Cup-Splash Guard (which is secured by three screws) should be removed periodically and wiped clean. For cleaning the Bowl Guard (including both Wire Cage Assembly and Splash Guard), refer to page 11. – 12 – MAINTENANCE WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT BEFORE BEGINNING ANY MAINTENANCE PROCEDURE. LUBRICATION Planetary The planetary oil should be checked periodically. To check, DISCONNECT ELECTRICAL POWER SUPPLY and remove the Drip Cup-Splash Guard, which is secured by three screws. Remove the fill plug (Fig. 6). Oil should be even with the bottom of the fill plug hole. If it is not, slowly add the recommended planetary lubri...