Évaluations - 4, GPA: 3.8
(
)
)
|
Facilité d'utilisation
5. When the timer reaches the end of the last programmed recipe step, the mixer stops; the beeper sounds; the selected recipe is displayed. View Recipe When the mixer is in RECIPE mode, you can view the step settings of any recipe. 1. Press the SELECT/SAVE button. A. Display will alternate between speed and time. B. The LED of the step being displayed will flash. 2. Use the arrow buttons to view the next step. 3. Use the Recipe selector to view other recipes. 4. Press PGM button to return to the RECIPE mode. NOTE: If the mixer is performing a recipe, the recipe will continue to operate in normal recipe mode sequence. PROGRAMMING RECIPE TIMER Fig. 16 HL200 is powered with display showing a mix time (Standard Mode) or recipe number (Recipe Mode). 1. If a mix time is displayed, Press RECIPE mode button. Display corresponds with position of recipe (speed) selector. 2. Press and hold TIME. Continue holding TIME, then press PGM and hold until rP1 is displayed (with step 1 blinking), buzzer sounds and programmed step LEDs are lit. 3. Use arrows to select recipe number (1-4) for programming. 4. Press SELECT/SAVE to enter program mode for the recipe number selected. Buzzer sounds and display alternates between speed and time to indicate programming mode. NOTES: • If a value has been assigned for a step number, that LED will be lit. • The LED for the selected step will blink. • If the default value is still assigned to a step, the LED will not be lit. • When programming, the Recipe and Time Selectors are disabled. SPEED SETTINGS TIME SETTINGS SPd 1 (DEFAULT) 00:00 – 15:00 minutes (10 second increments) SPd 2 End (default) SPd 3 Stir PAUS (pause – no mixing) 5. Use arrows to select step number (1 – 5). 6. Press SPEED. All characters will blink and buzzer will sound. A. Use arrows to select the mixing speed for selected step. B. Press SELECT/SAVE to set the speed. SAVE displayed momentarily and buzzer sounds. 7. Display alternates between speed and time to indicate programming mode. 8. Press TIME. Third digit will blink and buzzer will sound. A. Use arrows to select the mixing time (increments of 10 seconds) for selected step. NOTE: If all 5 steps are programmed, the recipe will terminate at the end of step 5. If fewer than 5 steps are used, the default time setting of END will terminate the recipe. B. Press SELECT/SAVE to set the time for the step. SAVE momentarily displayed and buzzer sounds. 9. Display alternates between speed and time to indicate programming mode. NOTE: LED of step programmed will be flashing. 10. Use arrows to select next step. 11. Repeat setting speed and time for additional steps and use SELECT/SAVE to save settings. 12. After all steps for recipe are programmed, press PGM to exit programming mode. Buzzer sounds and display will show recipe number that was programmed with the number blinking. 13. Press PGM to enter run mode. (Buzzer sounds) 14. Press STD to return to standard mode or set recipe selector to the desired recipe. 15. Select the recipe that you programmed and verify proper operation. UNLOADING 1. Open the bowl guard wire cage assembly. 2. Lower bowl support. 3. Remove the agitator from the agitator shaft. 4. Slightly lift the bowl off the pin (right side), pull bowl to the front and remove from the bowl support (left side). WIRE CAGE The bowl guard wire cage can be rotated out of the way to add ingredients or to access the bowl and agitator. Note how the plastic carriers allow the wire cage to ride around the circumference of the planetary drip cup. • Open the bowl guard wire cage: rotate it to your left (Fig. 9). • Close the bowl guard wire cage: rotate it to your right until it stops, closed position (Fig. 10). NOTE: The bowl guard wire cage must be returned to the closed position for the mixer to operate. Text Box: Text Box: Fig. 9 Text Box: Text Box: Fig. 10 Remove and Clean Bowl Guard Wire Cage (Fig. 11) 1. Rotate wire cage to your left until the three carriers align with the carrier escape slots in the circular ridge of the planetary drip cup. 2. Lift the wire cage straight up so the carriers escape from the slots on the drip cup. The bowl guard wire cage can now be removed by pulling toward you. 3. Wash the bowl guard wire cage in a sink, rinse with clear water, and dry with a clean cloth. 4. The splash guard can be wiped off and/or washed with a cloth or sponge using warm, soapy water. Rinse with clear water and dry with a clean cloth. Reinstall Bowl Guard Wire Cage 1. Position the ring of the bowl guard wire cage so the carriers are positioned above the slots in the planetary drip cup. 2. Lower the bowl guard wire cage so the carriers pass through the slots. 3. Rotate the bowl guard wire cage to your right until it contacts the stop, closed position. Text Box: Text Box: Fig. 11 Text Box: Escape Slots (3) AGITATORS AND ATTACHMENTS Attachments for attachment hub and agitators are covered in a separate Hobart Legacy Mixer Use and Application Handbook on the Mixer Operator Infor...