Évaluations - , GPA:
(
)
)
Fabricant : Briggs & Stratton
Taille : 2.62 mb
Nom Fichier : f1648b44-2040-3164-11ba-c2cd4adbe068.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
The ProjectPro™ nozzles vary the pressure and spray pattern as shown (Figure 13). Follow these instructions to change ProjectPro™ nozzles: 1. Engage trigger lock on spray gun. 2. Pull back collar on quick–connect and pull current ProjectPro™ nozzles off. Store ProjectPro™ nozzles in holder provided on the accessory tray. 3. Select desired ProjectPro™ nozzle: • For delicate rinse (lower pressure and higher flow), for gentle cleaning of cars/trucks, boats, RV’s, patio furniture, lawn equipment, etc., select yellow Delicate ProjectPro™ nozzle (Figure 14). Figure 12 — Typical Accessory Tray • NEVER exchange ProjectPro™ nozzles without engaging the trigger lock on the spray gun trigger. • DO NOT twist ProjectPro™ nozzles while spraying. A pressure washer produces a high pressure spray which increases risk of injury and damage to unit. CAUTION Figure 14 — Delicate Nozzle Delicate 40° Yellow 2350 PSI 2.7 GPM General 15° Orange 2675 PSI 2.5 GPM Max 0° Red 3000 PSI 2.3 GPM Black Use to apply detergent Figure 13 — Nozzle Spray Patterns Low Pressure High Pressure 13 • For general rinsing (medium pressure and medium flow), ideal for most all purpose cleaning such as home siding, brick patios, wood decks, driveways and sidewalks, garage floors, etc., select orange General ProjectPro™ nozzle (Figure 15). • For maximum rinsing (higher pressure and lower flow), for stubborn or hard to reach surface such as second story surfaces, paint removal, oil stains, rust removal or other stubborn substances (tar, gum, grease, wax, etc.), select red Max ProjectPro™ nozzle (Figure 16). • To apply detergent, applies project specific cleaners to help break down stubborn dirt and grime on a variety of surfaces, select black ProjectPro™ cleaning detergent nozzle (Figure 17). 4. Pull back on collar, insert new ProjectPro™ nozzle and release collar.Tug on ProjectPro™ nozzle to make sure it is securely in place. 5. For most effective cleaning, keep ProjectPro™ nozzle from 8 to 24 inches away from cleaning surface. If you get ProjectPro™ nozzle too close, you may damage cleaning surface. 6. DO NOT get closer than 6 inches when cleaning tires. Cleaning and Applying Detergent IMPORTANT: Use detergents designed specifically for pressure washers. Household detergents could damage the pump. Figure 16 — Max Nozzle Figure 17 — Cleaning Detergent Nozzle Section 4: Operation Figure 15 — General Nozzle CAUTION • Starting the engine without all the hoses connected and without the water turned ON will damage the pump. • Damage to equipment resulting from failure to follow this instruction will void warranty. You must attach all hoses before you start the engine. Section 4: Operation To apply detergent follow these steps: 1. Review ProjectPro™ nozzle use. 2. Prepare detergent solution as required by manufacturer. 3. Place small filter end of detergent siphoning tube into detergent container. CAUTION Keep the chemical injection tube from coming in contact with the hot muffler. • When inserting the filter into a detergent solution bottle, route the tube so as to keep it from inadvertently contacting the hot muffler. 4. Make sure black cleaning detergent nozzle is installed. NOTE: Detergent cannot be applied with the high pressure nozzles (Yellow, Orange or Red). 5. Make sure garden hose is connected to water inlet. Check that high pressure hose is connected to spray gun and pump and start engine. 6. Apply detergent to a dry surface, starting at lower portion of area to be washed and work upward, using long, even, overlapping strokes. 7. Allow detergent to soak in between 3–5 minutes before washing and rinsing. Reapply as needed to prevent surface from drying. DO NOT allow detergent to dry on (prevents streaking). IMPORTANT:You must flush the chemical injection system after each use by placing the filter into a bucket of clean water, then run the pressure washer in low pressure for 1-2 minutes. Pressure Washer Rinsing For Rinsing: 1. Engage trigger lock on spray gun. 2. Remove black cleaning detergent nozzle from nozzle extension. 3. Select and install desired high pressure nozzle following instructions “How to Use ProjectPro™ Nozzle System”. 4. Keep spray gun a safe distance from the area you plan to spray. WARNING High pressure spray could cause you to fall if you are too close to the cleaning surface. • Keep spray nozzle between 8 to 24 inches away from cleaning surface. • Operate this unit on a stable surface. • Be extremely careful if you must use the pressure washer from a ladder, scaffolding or any other relatively unstable location. • Firmly grasp spray gun with both hands when using high pressure spray to avoid injury when gun kicks back. 5. Apply a high pressure spray to a small area and then check the surface for damage. If no damage is found, you can assume it is okay to continue rinsing. 6. Start at top of area to be rinsed, working down with same overlapping strokes as you used for cleaning. Cleaning Detergent Siphoning Tube If you used the dete...