Évaluations - , GPA:
(
)
)
Fabricant : Briggs & Stratton
Taille : 8.45 mb
Nom Fichier : d74a8c87-31b0-8934-ede2-17e5569e87d6.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
Oil Fill Cap — Fill engine with oil here. Pressure Control Knob — Varies pressure of high pressure spray. Pump — Develops high pressure. Recoil Starter — Use for starting the engine manually. Run/Stop Switch — Set this switch to "Run" before using recoil starter. Set switch to "Stop" to switch off engine. Spray Gun — Controls the application of water onto cleaning surface with trigger device. Includes safety latch. Quick Connect Spray Tips — Detergent, 0°, 15°, 25°, and 40°: for various cleaning applications. Throttle Lever—Sets engine in starting mode for recoil starter. Water Inlet — Connect garden hose here. Spray Gun Nozzle Extension with Quick Connect High Pressure Hose Throttle Lever Choke Lever Fuel Valve Recoil Starter Run/Stop Switch (on front of engine) Air Filter Fuel Tank Water Inlet Pressure Control Knob Pump equipped with Automatic Cool Down System High Pressure Outlet with Quick Connect Oil Fill Cap Quick Connect Spray Tips KNOW YOUR PRESSURE WASHER Read this operator’s manual and safety rules before operating your pressure washer. Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and adjustments. Save this manual for future reference. ASSEMBLY ASSEMBLY IMPORTANT: Read entire operator’s manual before you attempt to assemble or operate your new pressure washer. Unpack the Pressure Washer 1. Remove everything from carton except pressure washer. 2. Open carton completely by cutting each corner from top to bottom. 3. Remove pressure washer from carton. Carton Contents Items in the carton include: • Main unit • High pressure hose • Spray gun with quick connect fitting • Nozzle extension with quick connect fitting • Handle • Parts Bag (includes the following): • Hose fittings • Quick connects • Bag containing 5 multi–colored quick connect spray tips • Safety goggles • Operator’s manual • Engine operator’s manual • Maintenance kit • Handle fastening hardware kit (which includes): • Carriage bolts (2) • Plastic knobs (2) If parts are missing or damaged, contact the local Briggs & Stratton service center. PREPARING PRESSURE WASHER FOR USE To prepare your pressure washer for operation, you will need to perform these tasks: 1. Attach handle to main unit. 2. Verify oil dipstick has been installed into pump (Figure 2). Figure 2 — Pump Dipstick Pump Oil Dipstick 3. Add oil to engine crankcase. 4. Add fuel to fuel tank. 5. Connect high pressure hose to spray gun and pump. 6. Connect water supply to pump. 7. Attach nozzle extension to spray gun. 8. Select/attach quick connect spray tip to nozzle extension. Attach Handle NOTE: All assembly operations given in this section will be described from the perspective of assembling the pressure washer from the rear. 1. Place handle assembly onto handle supports connected to main unit. Make sure holes in handle align with holes on handle supports (Figure 3). Align Holes Handle Handle Supports Figure 3 — Attach Handle to Base 7 ASSEMBLY NOTE: It may be necessary to move the handle supports from side to side in order to align the handle so it will slide over the handle supports. 2. Insert carriage bolts through holes from outside of unit and attach plastic knob on inside of handles (Figure 4). Tighten by hand. Figure 4 — Secure Handle 3. Insert multi–colored spray tips in spaces provided in handle. Add Engine Oil and Fuel • Place pressure washer on a level surface. CAUTION Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure. • Refer to engine manual for oil and fuel fill information. • Damage to equipment resulting from failure to follow this instruction will void warranty. • Refer to engine operator’s manual and follow oil and fuel recommendations and instructions. NOTE: Check oil often during engine break–in. Refer to engine operator’s manual for recommendations. Connect Hose and Water Supply to Pump IMPORTANT: To avoid pump damage, you must assemble the nozzle extension to the spray gun and attach all hoses before you start the engine. 1. Uncoil high pressure hose and attach quick connect end of hose to base of spray gun (Figure 5). Pull down on collar of quick connect, slide onto spray gun and let go of collar.Tug on hose to be sure of tight connection. NOTE: Remove and discard all pump shipping caps before attaching hoses. 2. Similarly, attach other end of high pressure hose to high pressure outlet on pump (Figure 6). Pull down on collar of quick connect, slide onto pump and let go of collar. Pull on hose to be sure of tight connection. Connect high pressure hose here. Figure 5 — Connect High Pressure Hose to Spray Gun Connect high pressure hose here Figure 6 — Connect High Pressure Hose to Pump 8 ASSEMBLY 9 3. Before connecting garden hose to water inlet, inspect inlet screen (Figure 7). Clean screen if it contains debris or replace if damaged. DO NOT RUN PRESSURE WASHER IF SCREEN IS DAMAGED. 4. Run water through garden...