Évaluations - 2, GPA: 4.5 ( )

Fabricant : Nilfisk-Advance America Taille : 1.13 mb Nom Fichier : Langue d'enseignement:

The machine will restart after a few minutes when the thermal sensor has cooled. 4 2 Description 2.1 Application 2.2 Operation elements and model survey This high-pressure washer has been developed for domestic use within: - Car, motorbike, boat, caravan, trailer, patio/drive/flagstones, woodwork, brickwork, barbecue, garden furniture, lawn mower See illustration at the end of this manual. 1 Start/stop switch 2 Water inlet with filter (2a) 3 High pressure connection 4 High pressure hose 5 Electric cable 6 Click & Clean spray lance 7 Spray gun with lock (7a) 8 Click & Clean Tornado® nozzle 9 Click & Clean Powerspeed® nozzle Only use the high-pressure washer for purposes described in this manual. The safety precautions must be observed to prevent damage to the machine, the surface to be cleaned or severe personal injuries. 10 Foam sprayer 11 Nozzle cleaning tool 12 Lance and nozzle holder 13 Model tag 14 Holder for electric cable (not standard on all models) 15. Hexagon key Specifi cations: See model tag (13) of machine. We reserve the right to alter the specifi cations. 5 6 3 Before you start using your pressure washer 3.2 Mounting of quick coupling 1. Screw the quick coupling tight on to the water inlet (2). Note: The inlet fi lter (2a) must always be fi tted in the water inlet pipe to fi lter out sand, lime stone and other impurities as these will damage the pump valves. Caution: Failure to fi t the fi lter will invalidate the guarantee. 3.1 Mounting of trolley handle (models with trolley handle) 3.3 Mounting of high pressure hose on spray gun 1. Attach the high pressure hose (4) to the spray gun (7). Detach the high pressure hose by pressing the pawl (A). 1. Place the trolley handle on the machine. 2. Secure the handle by mounting the 2 screws. Use the enclosed hexagon key. .. 7 4 Operating your pressure washer 4.1 Connection of high pressure hose 1. Mount the high pressure hose on the outlet (3). 4.2 Mounting of spray lance and Click & Clean nozzles 1. Push the spray lance (6) into the spray gun (7) and screw it on. Note: The spray lance (6) has a built-in low pressure nozzle that can be used for fl ushing away dirt. 2. Attach the nozzle. Warning: When attaching the Click & Clean nozzles, the pawl on the side of the spray lance (6) should come out again. Note: The foam sprayer (10) features a swivel lock, which must be positioned in the hole in the Click & Clean spray lance (6). Press the pawl to detach the Click & Clean nozzle. .. 4.3 Water connection 4.4 Start and stop of the machine An ordinary 1/2" garden hose of min. 10 m and max. 25 m will be suitable. NOTE: Connection to the public mains according to regulations. The spray lance is affected by a thrust during operation - therefore always hold it firmly with both hands. IMPORTANT: Point the nozzle at the ground. 1. Check that the machine is in uprigth position. NOTE: Do not place the machine in high grass! 2. Release the trigger lock (7a). 3. Activate the trigger of the spray gun and let the water run until all air has escaped from the water hose. 4. Press the Start/stop switch "I" (1). 5. Activate the trigger of the spray gun. Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be cleaned. IMPORTANT! Only use water without any impurities. If there is a risk of running sands in the inlet water (i.e. from your own well), an additional filter (106411231) should be mounted. 1. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrating the machine. Note: Check that the filter is fitted in the water inlet pipe and that it is not clogged up. 2. Connect the water hose to the water supply by means of the quick connector (inlet water, max. pressure: 10 bar, max. temperature: 40°C). 3. Turn on the water. Do not cover the machine during operation or use it in a room without adequate ventilation ! Note: If the ma chine is left or not used for 5 minutes, it must be switched off on the start/stop switch "O" (1): 1. Press the start/stop switch "O". 2. Disconnect the electrical plug from the socket. 3. Shut off the water supply and activate the trigger to relieve the machine of pressure. 4. Lock the spray gun (7a). When releasing the trigger of the spray gun, the machine automatically stops. The machine will start again when you re- activate the spray gun. 8 9 5.2 Winding up of electric cable and high pressure hose 5 After using your pressure washer To avoid accidents, the electric cable and the high pressure hose should always be winded carefully up around the handle. C 110.3 / C 110.3 X-TRA: Wind up the cable on the appropriate hook. 5.1 Storing the washer The machine should be stored in a frost-free room! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1. Stop the machine (press the start/stop switch “O” (1) and detach water hose and accessory. 2. Restart the machine and activate the trigger. Let the machine run until no m...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :