Évaluations - 5, GPA: 4.4
(
)
)
|
Facilité d'utilisation
WARNING Theengineexhaustfromthisproductcontains chemicals known to the State of California to causecancer,birthdefectsorotherreproductive harm. CAUTION Risk of Asphyxiation – Use this product only in a well ventilated area. ¦ Operate and fuel machine in a well ventilated area, free of devices featuring an open pilot or flame such as boilers, washer heaters, etc. CAUTION Risk of Fire – Do not add fuel when the product is operating. ¦ Do not operate if fuel has been spilled. Instead, move the machine to a different location and avoid creating sparks. ¦ The machine has hot surfaces which can cause burns. Operate the unit in a safe environment and away from children. ¦ Do not touch hot surfaces or allow accessories to contact hot surfaces. ¦ Do not allow the high pressure hose to come into contact with the muffler guard. ¦ Do not leave the machine running una tended. ¦ Avoid tipping the machine on its side. 4 English SAVE THESE INSTRUCTIONS WATER SUPPLY (Cold Water Only) CAUTION When connecting the water inlet to the water supply mains, local regulations of your water company must be observed.In some areas the unit must not be connected directly to the public drinking water supply.This is to ensurethatthereisnofeedback ofchemicals in to the water supply.Direct connection via a receiver tank or backflow prevented, for example, is permitted.Dirt in the feed water will damage the unit.To avoid this risk, we recommend fitting a water filter. ¦ Garden hose must be at least 5/8 inch diameter. ¦ Flow rate of water supply must not fall below 2.5 GPM (gallons per minute) ¦ Flow rate can be determined by running the water for one minute into an empty 5-gallon container. ¦ The water supply temperature must not exceed 104°F/40°C. ¦ Never use the pressure washer to draw in water contaminated with solvents, e.g. paint thinners, gasoline, oil, etc. ¦ Always prevent debris from being drawn into the unit by using a clean water source. Use additional water filter. ASSEMBLY INSTRUCTIONS Required Tools (included) Description 7/16" (or 11mm) Wrench Stamped Hardware (included) Description Purpose Illustration Qty A Joint Joint Assembly 2 B 1/4" Nut Joint Assembly 6 English 5 6 English STEP 1: Insert joints (A) into handle. Use one 1/4" bolt (C) and tighten with one 1/4" nut (B) on each side. Hand tighten. STEP 2: Attach the handle to the frame of the pressure washer. Align holes, insert one 3/8" bolt (E), and tighten the knob (D) on each side. Description Purpose Illustration Qty C 1/4" Bolt Joint Assembly 6 D Knob Joint Assembly 2 E 3/8" Bolt Joint Assembly 2 F Nylon Rivet Nozzle Holder Assembly 4 G Tank Detergent tank 1 Assembling CHAUD! D D A A B B C C E English 7 STEP 3: Mount the detergent tank with enclosed nylon rivets to the bumper. F G STEP 4: Place the quick connect nozzles in the nozzle holder. STEP 7: Pull back the spring loaded collar at the spray gun and insert the high pressure hose. STEP 5: Attach the wand to the spray gun. STEP 6: Pull the spring-loaded collar of the wand back to insert your choice of quick connect nozzle. Release the collar and push the nozzle until the collar clicks. Release the collar and push the nozzle until the collar clicks. WARNING High pressure in nozzle area. Risk of injury caused by improperly locked nozzle. ¦ Make sure you hear a "click" when inserting the nozzle tip in to the wand. ¦ Pull the nozzle to make sure it is seated properly before operating your unit. WARNING High pressure in quick connect area. Risk of injury caused by improperly locked high pressure hose. ¦ Make sure you hear a "click" when inserting the high pressure hose in to the quick connection. ¦ Pull the high pressure hose to make sure it is seated properly before operating your unit. OPERATING INSTRUCTIONS CAUTION Engine Shipped without oil. Before starting engine, fill with oil. Do not over-fill. Do not run the engine with a high or low oil level as this can cause engine damage. If you have further questions regarding the engine, please refer to the engine manual included with the unit. STEP 1: Check oil level. Oil level should always be between the "FULL" and "ADD" marks on the dipstick. Be sure the machine is level when checking the oil level. (Refer to the engines operating manual for seasonal grades.). We recommend that the oil be changed after the first 5 hours of use, then once every 50 hours. STEP 2: Fill gas tank with unleaded gasoline. Do not use leaded gasoline. Do not add oil to the gasoline. STEP 3: Pull back the spring loaded collar at the high pressure outlet and insert the high pressure hose. Release the collar and push the high pressure hose until the collar clicks. WARNING High pressure in quick connect area. Risk of injury caused by improperly locked high pressure hose. ¦ Make sure you hear the "click" when inserting the high pressure hose into the quick connection. ¦ Pull the high pressure hose to make sure it is seated properly before operating your unit. STEP 4: Connect garden hose to units`s wa...
Ce manuel est également adapté pour les modèles :Équipement de lavage - G2600XC (2.5 mb)