Évaluations - 3, GPA: 3
(
)
)
|
Facilité d'utilisation
Hand tighten. 5. Remove tie wrap off of high pressure hose. Unwind high pressure hose and attach the threaded end to the gun. Tighten with adjustable wrench. 6. Connect high pressure hose to outlet on pressure washer and hand tighten firmly. HIGH PRESSURE HOSE NOTE: Always keep hose away from engine muffler. D20590 6-ENG 7. Place assembled gun and wand on pressure washer holder. Cord Wire Bracket Gun/Wand Holder 8. Place pull cord into the wire bracket holder. • Pull the cord under the wire bracket to the right of the wire loop. • Lift the pull cord handle up and slide the cord to the left, sliding the cord into the wire loop. • Next slide handle behind the wire bracket to the left of the wire loop. • Engine recoil will pull the cord into its final position. Checklist Before going any further please review the following: • Be sure you have completed assembly instructions. • Double check all fittings to be sure they are tight. IMPORTANT: Before any attempt to start your pressure washer be sure to check engine oil (See Engine Oil on page 8.) OPERATION PUMP- Develops high pressure. ENGINE RUN/STOP SWITCH- Sets engine in starting mode for recoil starter — Stops running engine. RECOIL STARTER- Used for starting the engine manually. SPRAY GUN ASSEMBLY (Contains Gun and Wand) Controls the application of water onto cleaning surface with trigger device. OIL FILL- Port where engine oil is poured. GAS TANK/CAP- Cap is removed and unleaded gasoline is poured. HIGH PRESSURE OUTLET- Connection for high pressure hose. CHOKE- Used to start a cold engine. CONNECTION SPRAY GUN ASSEMBLY HIGH PRESSURE HOSE HANDLE HIGH PRESSURE OUTLET PUMP WATER INLET OIL FILL GAS TANK/ CAP RECOIL STARTER ENGINE STOP/ START CHOKE Know Your High Pressure Washer Read this Owner’s Manual and Safety Rules before operation of your High Pressure Washer Compare this illustration with our pressure washer to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. D20590 7-ENG WARNING: Read Owner’s Manual. Do not attempt to operate equipment until you have read Owners Manual for Safety, Operation, and Maintenance Instructions. Note: Included with your unit is a video cassette that demonstrates how to operate your pressure washer. If you have a video cassette recorder you should view the video before operation. WARNING: Never adjust spray pattern when spraying. Never put hands in front of spray nozzle to adjust spray pattern you could be injured. Stopping Your Pressure Washer CAUTION: Do not run pump without the water supply connected and turned on. Failure to do so will result in pump damage. • Move throttle control to the stop position to turn pressure washer off. THROTTLE CONTROL • Simply shutting OFF engine will not release pressure in the system. After engine has stopped, squeeze the trigger on the spray gun for about 3 seconds to relieve pressure. Spray stream will decrease in length. IMPORTANT: This unit is equipped with a thermal relief valve. If unit is allowed to run for several minutes without pressing the trigger on the spray gun, several drops of water may be released through this valve to cool the unit. This small amount of water will drip from the bottom of the pump. Before Starting The Engine To operate the engine you will need to do the following. CAUTION: Always check engine oil level before every start. Running engine low of oil or out of oil could result in serious damage. Engine Oil Your unit has been shipped without oil in the engine. A bottle of SAE 30 weight oil is included in the carton. Remove oil dip stick located on top of the engine. Oil capacity is about 20 ounces of oil. The oil dip stick is clearly marked with a line that tells you when unit has enough oil. To check oil, place dipstick into oil fill. Tighten dipstick then remove. Do not fill above this point. Pour slowly. NOTE: When adding oil to the engine crankcase, use a high quality detergent oil classified “For Service SF, SG, SH”, rated SAE 30 weight. Use no special additives. Select the oil’s viscosity grade according to your expected operating temperatures. colder <——-----———40°F——————> warmer Synthetic 5W-30 l SAE 30 Although multi-viscosity oils (5W30, 10W30, etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 40°F. Check your engine oil level more frequently to avoid possible damage from running low on oil. Oil sump capacity is 20 ounces. Gasoline Your pressure washer engine is 4 cycle. Use unleaded fuel only. CAUTION: Do not overfill the fuel tank. Always allow room for fuel expansion. WARNING: Never fill fuel tank indoors. To avoid explosion and injury, never fill fuel tank when engine is running or hot. Do not smoke or have open flame when filling fuel tank. D20590 8-ENG Use clean, fresh, regular unleaded gasoline with a minimum of 85 octane. Do not mix oil with gasoline. If unleaded fuel is unavailable leaded fuel may be used. IMP...
Ce manuel est également adapté pour les modèles :Équipement de lavage - D20590 (3.55 mb)