Évaluations - , GPA: ( )

Instructions Campbell Hausfeld, Modèle BUILT TO LAST PW3002

Fabricant : Campbell Hausfeld
Taille : 2.72 mb
Nom Fichier : 1b15e38e-b67b-4dd3-b5f2-4e043eaf8b66.pdf

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

To depressurize, turn engine/motor off, turn water supply off and squeeze gun trigger 2-3 times. 5. After each use, wipe all surfaces of the pressure washer with a clean, damp cloth. • Do not store the pressure washer outdoors. • Do not store the pressure washer where it might freeze unless it has been properly winterized. 9. Storage LONG TERM STORAGE INSTRUCTIONS (MORE THAN 30 DAYS IN STORAGE) 1. Remove fuel from the tank and run the pressure washer in a normal operating mode until the engine stops from a lack of fuel. Normal operating mode means actually spraying water from the gun while the engine is running. Alternate method – Add fuel stabilizer to gas in the tank and run in normal operating mode for at least five minutes. 2. Stop the engine, turn off the water supply, and trigger the gun to release pressure in the high-pressure hose. 3. Disconnect the water supply and high pressure hose from the pump. 4. Allow the engine to cool. 5. Disconnect the spark plug wire and remove the spark plug. 6. Pour 1/2 oz. of engine oil into the spark plug hole. Never pull the starter rope on the engine when the spark plug is removed unless the spark plug hole is covered. Fuel vapor from the hole can ignite by a spark. 7. Place a rag over the spark plug hole and slowly pull the starter rope several times to distribute the oil. WINTERIZING INSTRUCTIONS 1. Follow and complete the Long Term Storage Instructions above. 2. Disconnect the spark plug wire. 3. Disconnect the high pressure hose from the pump. 4. Insert a 12” to 14” piece of garden hose into the pump inlet. 5. Place a funnel in the other end of the garden hose. Read the manufacturer’s instructions for safe handling and disposal of RV antifreeze. 6. Pour approximately 6 oz. of RV antifreeze into the funnel. 7. Pull the starter rope several times until the RV antifreeze comes out of the pump outlet. 8. Disconnect the high pressure hose from the gun and drain the hose. Hold the gun and lance in a vertical position and squeeze the trigger to drain the water out. TIPS FOR EXTENDING THE LIFE OF YOUR PRESSURE WASHER 1. Never operate the unit without water. 2. Your pressure washer is not meant to pump hot water. Never connect your pressure washer to a hot water supply as it will significantly reduce the life of the pump. 3. Running the unit for more than one minute without spraying water causes heat to build up in the pump. Running the unit without spraying water can damage pump components. 9 Pressure Washer Maintenance Observe regular maintenance intervals to ensure maximum performance and life from the pressure washer. Refer to the schedule for recommended maintenance. If you operate the pressure washer in dusty conditions, perform maintenance checks more often. ENGINE OIL CHANGING INSTRUCTIONS Before tipping the engine or equipment to drain oil, drain fuel from the fuel tank. NOTE: Change oil while the engine is cool. 1. Disconnect the spark plug wire from the spark plug. 2. Locate, and if accessible, remove the engine oil drain plug (if the engine is equipped with an oil drain plug, the drain plug is located in at least one of the locations shown in Figure 18). If the engine oil drain plug is not accessible or if the engine is not equipped with an oil drain plug, tip the unit on its side to drain the oil out of the oil fill tube (See Figure 18). NOTE: If draining oil from the oil fill tube, keep the air cleaner side up. Service Record 3. Drain old oil. 4. Replace the drain plug and set the unit upright. 5. Refill the unit with new oil of a recommended type and quantity. Fill the unit to the proper level shown on the dipstick (if provided). Otherwise, fill the unit to the top of the oil filler neck. PUMP OIL CHANGING INSTRUCTIONS Changing or refilling the oil in the pump requires removal of the pump from the engine and should not be required unless oil has leaked out due to worn or damaged oil seals in the pump. If oil has leaked out of the pump, bring the pressure washer to a certified Campbell Hausfeld service center for repair. Figure 18 - Oil Drain Locations 1. Oil fill tube 2. Plug on side of engine base 3. Plug at bottom of engine Date Maintenance performed Replacement components required 10 Pressure Washer Maintenance (Continued) Maintenance Schedule Technical and Consumer Information Maintenance Action neededSchedule Vertical Oriented Pressure Washers Daily • Check water inlet screen and Engine Oil Type SAE 10W-30 SAE 30W (Above 60° F) filter. • Check engine oil levels. Fill as necessary. • Check gasoline level. Fill as necessary. After first 5 hours of • Change engine break-in oil. operation Use SAE30 or 10W-30 detergent oil. Every 25 hours of operation • Change oil if operating under heavy load or high ambient temperature. • Remove and clean foam pre- cleaner or foam air filter (if applicable). Wash with water and mild detergent. Dry thoroughly. Rub with oil and Engine Oil Capacity Tecumseh engines 21 fl. oz. Engine Fuel Capa...