Log:
Évaluations - 3, GPA: 4.7 ( )

Instructions Maxus, Modèle MX5223

Fabricant : Maxus
Taille : 3.82 mb
Nom Fichier : bb07cc9e-547e-4b90-80f1-7b6d7a49d94b.pdf
Langue d'enseignement: enes
Aller à la télécharger



Facilité d'utilisation


Worn water seals, abrasives in water, or natural 3. Check filter. Replace water seals. See service center wear 4. Clean inlet and discharge valve assemblies. Check 4. Fouled or dirty inlet or discharge valves filter 5. Restricted inlet 5. Check garden hose, may be collapsed or kinked. Check inlet water flow 6. Worn inlet or discharge valves 6. Replace worn valves 7. Leaking high pressure hose 7. Replace high pressure hose 8. Pump drawing in air 8. Ensure hoses and fittings are tight 9. Unloader valve seat faulty or worn 9. Check and replace Water leakage from under Worn water seals Install new water seals. See service center pump manifold Water in pump crankcase 1. Humid air condensing inside crankcase 1. Change oil as specified in maintenance schedule (milky oil) 2. Oil seals leaking 2. Install new oil seals. See service center Frequent or premature 1. Scored damaged or worn plungers 1. Install new plungers. See service center failure of the pump water 2. Abrasive material in the fluid 2. Install proper filtration on pump inlet plumbing seals 3. Inlet water temperature too high 3. Check water temperature; may not exceed 100o F. 4. Overpressurizing pump 4. Do not modify any factory set adjustments. 5. Excessive pressure due to partially plugged 5. Clean or replace tip. or damaged tip 6. Pump running too long without spraying 6. Never run pump more than 2 minutes without spraying 7. Pump running dry 7. Do not run pump without water Strong surging at the inlet and low pressure Foreign particles in the inlet or discharge valve or worn inlet and/or discharge valves Clean or replace valves. See service center Oil leakage between the engine and the pump Worn oil seals and/or o-ring Replace oil seals and/or o-ring. See service center Fluctuating pressure 1. Valve worn, dirty or stuck 1. Check and replace 2. Pump drawing in air 2. Ensure hoses and fittings are tight. Purge air from garden hose 3. Tip clogged 3. Check or replace Pressure drops after period 1. Worn pump water seals 1. Check and replace of normal use 2. Nozzle worn 2. Check and replace 3. Valve worn, dirty or stuck 3. Check, clean or replace 4. Unloader valve seat worn or dirty 4. Check, clean or replace 5. Nozzle in low PSI position 5. Pull back nozzle to high pressure position 12 MX5223, MX5333, and MX5433 Troubleshooting Chart - Gasoline Powered Pressure Washers Only Symptom Possible Cause(s) Corrective Action(s) Pump noisy / pump runs 1. Pump drawing in air/low water supply 1. Ensure fittings are tight. Increase water pressure rough 2. Valves dirty or worn 2. Check, clean or replace 3. Worn bearings 3. Check and replace 4. Water too hot 4. Reduce temperature below 100o F Pressure washer will not 1. Not using soap tip 1. Install 65 degree (black) soap tip spray detergent 2. Clog, kink, or hole in detergent suction hose 2. If clean, unkink or replace hose. 3. Hose length too long 3. Use only hose length provided with initial purchase of pressure washer. Detergent suction will not function if more than one section of hose is attached to unit. 4. Lance not functioning properly 4. Remove lance from gun. If detergent is dispensed through gun, the lance must be replaced. If no detergent is dispensed through gun, remove 1” tapered detergent barb from pump. Clean the barb, and make sure that ball and spring are properly aligned with tapered portion of the spring facing the ball. The ball should be on top of the spring. Notes 1 113 33 Operating Instructions and Parts Manual Limited Warranty 1. DURATION: From the date of purchase by the original purchaser as follows: Five Years 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Mundy Memorial Drive, Mount Juliet, TN 37122, Telephone: 1-888-MAXUS4U 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld pressure washer. 4. WHAT PRODUCTS ARE COVERED UNDER THIS WARRANTY: Any Campbell Hausfeld Pressure Washer supplied or manufactured by the Warrantor. 5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects on material and workmanship which occur within the duration of the warranty period with the exceptions noted below. 6. WHAT IS NOT COVERED UNDER THIS WARRANTY: A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this pressure washer is used for commercial, industrial or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States do not allow limitation on how long an implied warranty lasts, so the above limitations may not apply to you. B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRESSURE WASHER. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above...

Ce manuel est également adapté pour les modèles :
Équipement de lavage - MX5333 (3.82 mb)
Équipement de lavage - MX5433 (3.82 mb)

Écrivez votre propre critique du dispositif



Texte du message
Votre nom :
Entrez les deux chiffres :
capcha





catégories