1) Turn on the water supply tap fully. 2) Release the safety catch (D). 3) Depress the gun trigger for a few seconds and start up the appli ance using the starter device (ON/1). AS models -In AS models with automatic delivery ow cut-o system: -When the gun trigger is released the dynamic pressure automati cally cuts out the motor (see g.4); -When the gun trigger is depressed the automatic drop in pressure starts the motor and the pressure is restored after a very slight delay; -If the AS is to f

If the supply cord is damaged, it must be replaced by themanufacturer, an authorized Black & Decker Service Centre or an equally qualied person in order to avoid ahazard. If the supply cord is replaced by an equally qualied person, but not authorized by Black & Decker, the warranty will lose eect. ACCIDENT HAZARD DISCHARGE residual pressure before disconnecting the unit hose. INJURY HAZARD 2.2.8 Before using the appliance, CHECK every time that the screws are fully tightened and that there are n

To prevent damage to the appliance, when running do not stop the water jet for more than 10 minutes at a time. 7.3 Stopping the appliance 1) Set the starter device switch on (OFF/0). 2) Depress the gun trigger and discharge the residual pressure inside the hoses. 3) Engage the gun safety catch (D). English 19 7.4 Restarting 1) Release the safety catch (D). 2) Depress the gun trigger and discharge the residual air inside the hoses. 3) Set the starter device on (ON/1). 7.5 Storage 1) Switch the ap

The appliance should only be connected to a mains power supply equipped with an adequate earth connection and a d erential security breaker (30 mA) to cut the electricity supply in the instance of a short circuit. 5.3.1 Use of extension cables Use cables featuring “IPX5” protection level. The cross-section of the extension cable should be proportionate to its length; the longer it is, the greater its cross-section should be. See table I. 5.4 Water supply connection Caution -Danger! Only clean or

Press spring buttons (R) of handle (K) inward as handle tubes are pushed down fully into lower tubes (N), and both spring buttons protrude out through holes in lower tube (N) completing assembly. Upper Cord Wrap Hook Assembly - PW1750 Insert cord wrap top hook (M) into the rear slots in handle (K) by pushing upward and inward to snap in place. Drive two 1/2” self tapping screws included in cord hook bag through cord wrap holes into handle as shown until tight. DO NOT over tighten. 6 High pressur

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. DANGER: Improper connection of the equipment-grounding conductor can result in a risk of electrocution. Check with a qualified electrician or service personnel if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the product - if it will not fit the outlet, have a proper outlet installed by a qualified el

4 A. High pressure water outlet (OUTLET) B. Pump Quick Connector C. High pressure turbo wand D. Adjustable fan wand E. Wheels E1. Wheel Cap F. Gun F1. High pressure hose connector F2. Gun safety catch G. Power supply cord with GFCI H. Hardware bag I. On/off switch J. Garden hose Quick Connector K. Handle L. Removable detergent tank with cap M. Cord wrap top hook N. Steel Support tubes O. Nozzle Cleaning tool P. Black top housing Q. Orange main housing F F1 F2 H O I I K L J M N O B E1 E D P Q C O

2.2.12 rEAd iNSTruCTioN mANuAL BEForE uSE 15 ENGLISH 3 GENERAL INFORMATION (FIG.1) 3.1 Use of the manual This manual forms an integral part of the appliance and should be kept for future reference. Please read it carefully before installing/ using the unit. if the appliance is sold, the Seller must pass on this manual to the new owner along with the appliance. 3.2 Delivery The appliance is delivered partially assembled in a cardboard box. The supply package is illustrated in Fig.1. 3.2.1 Documen

V..............volts A..............amperes Hz............hertz W ............watts min ..........minutes ............alternating current ........direct current no ............no load speed ............Class II Construction …/min......revolutions or reciprocation per minute ............earthing terminal ............safety alert symbol SAVE THESE INSTRUCTIONS 3 4 A. Water outlet (OUTLET) B/B1 Water inlet with filter (INLET) C. High pressure turbo wand D. Adjustable fan wand E. Wheels F. Revolving

SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPANOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACION, CENTROS DE SERVICIOY POLIZA DE GARANTIA. ADVERTENCIA: LEASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO. 598121-00 Pressure Wash Revised 11/24/03 2:00 PM Page 2 IMPORTANT SAFETY INSTRUCTIONS WARNING: When using this product, basic precautions should always be followed, including the following: 1. Read and understand all instructions before using the product. 2. To reduce the risk of injury, close