NOTE: Stand on a stable surface and grip gun/spray wand firmly with both hands. Expect the gun to kick when triggered. 10. Release trigger to stop water flow. 11. Adjust spray for the task being performed by changing quick connect nozzle. See How To Use Spray Wand instructions in this section. SHUTTING DOWN 1. After each use, if you have applied chemicals, place chemical hose into container of clean water and draw clean water through chemical injection system to rinse system thoroughly. NOTE: Fa

1 YEAR -Limited warranty on all other air compressor components. 2 YEARS -Limited warranty on electric generator alternators. 1 YEAR - Limited warranty on other generator components. 2 YEARS -Limited warranty on pneumatic air tools as described in Porter-Cable general catalog. 1 YEAR -Limited warranty on pressure washers used in consumer applications (i.e. personal residential household usage only). 90 DAY -Pressure washers used for commercial applications (income producing) and service parts. 1

. . . . . . . . . . . . . .6 Flush Before Using Equipment . . . . . . . . . . . . . .6 Integrated Air Control Module . . . . . . . . . . . . . . .6 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 PressureRelief Procedure . . . . . . . . . . . . . . . . .9 Cleaning Solutions . . . . . . . . . . . . . . . . . . . . . . .9 Flushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Starti

Important Safety Instructions Read all warnings and instructions in this manual and in your respective pump manual. Save these instructions. See page 3 for model information, including maximum working pressure. TI11267A Cart Mount Packages Wall Mount Packages TI11273A II 2 G Contents Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Related Manuals . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

NO. DESCRIPTION QTY NO. NO. DESCRIPTION QTY 1 802–319 MANIFOLD 1 27 803–273 SCREW, Cap, socket hd. 5 2 801–651 SCREW, Cap, socket hd. 8 28 KIT 6 O–RING 3 801–652 WASHER, Lock 8 29 802–345 GAUGE, Sight 1 4 KIT 1 O–RING 30 802–793 PLUG, Oil Drain 1 5 KIT 1 SEAT, Valve 31 803–328 CRANKSHAFT 1 6 KIT 1 PLATE, Valve 32 803–275 PIN, Wrist 3 7 KIT 1 SPRING 33 802–794 KEY 1 8 KIT 1 GUIDE, Valve 34 803–276 ROD, Connecting 3 9 KIT 4 O–RING 35 803–277 WASHER, Flat 6 10 KIT 4 CAP 36 803–278 WASHER, Lock 6 11

8. Install the capscrews and washers finger–tight. Torque the screws to 21.7 ft–lb (29 Nm) following the tightening pattern (Figure 4). Uneven tightening may cause the manifold to bind or jam. 1 4 23 5 8 7 6 3. Carefully examine each plunger for any scoring or Figure 4 cracking and replace as necessary. . . Servicing the V–Packings 5. Thoroughly clean the packing cavities and examine. NOTE: There are two types of packing kits: one is just packings, the other includes the packings, rings and reta

See Operation section. Chemical Hose (not shown): Allows cleaners or cleaning solvents to be mixed with the pressurized water stream. See How To Siphon Chemicals/Cleaning Solvents in Operation section of this manual. 8- ENG D25805 BASIC ELEMENTS OF ENGINE Refer to the engine manual for location and operation of engine controls. Choke Control: Opens and closes carburetor choke valve Throttle Control Lever: Controls engine speed. Starter Grip: Pulling starter grip operates recoil starter to crank

HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY. FOR PROFESSIONALUSE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safety Pressure Relief Procedure This pressure washer generates very high fluid To reduce the risk of serious bodily injury, including fluid pressure. Spray from the gun, leaks or ruptured injection and splashing in the eyes oron the skin, components can inject fluid through your skin and into always f

BOX 1441 MINNEAPOLIS, MN 55440- 1441 Copyright 2002, Graco Inc. is registered to I.S. EN ISO 9001 Hydra--CleanR 4043, 16 HP Engine Hydra--Cleanr 4043 Pressure Washer P/N 800707, Series B 4000 psi (27.6 MPa, 276 bar) Operating Pressure 4300 psi (29.6 MPa, 296 bar) maximum Working Pressure 308532S Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. See page 2 for Table of Contents. 6811B Table of Contents Warnings ..............................

If extremely worn a reverse pliers may be used. Reassembly: V–Packing Models: 1. Lubricate high pressure packing area in manifold. 2. Insert male adapter with notches down and “v” side up. 3. Lubricate v–packings and install one–at–a–time with grooved side down. 4. Next install female adapter with grooved side down. 5. Examine seal case o–ring and replace if worn. Lubricate new o–ring before installing. 6. Thread seal case into manifold and tighten with key wrench. High Pressure Seal Models: 1.