Évaluations - , GPA: ( )

Instructions Audiovox, Modèle ADV350S

Fabricant : Audiovox
Taille : 82.49 kb
Nom Fichier :

Langue d'enseignement:

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

Le document est chargé, s'il vous plaît patienter

Téléchargez votre Fermer

By bending the cut back and forth several times, the plastic will break cleanly at the cut. D) Check the fit of the trimmed console and make any minor adjustments necessary. 4) The mini-console can be painted or covered with a material that matches the headliner before assembling the mini-console to video monitor. 5) The finished mini-console should be attached to the video monitor, then attach the assembly to the roof. Tape marker to screwdriver. Starting at your mark for the lowest point, trace the contour of the roof Lowest point mark Cut line Headliner Tape marker to screwdriver. Starting at your mark for the lowest point, trace the contour of the roof Lowest point mark Cut line Headliner -4 MOUNTING THE MINI-CONSOLE Roof Roof Support Headliner 12”x9”x3/4” Plywood Block (4) Self-Tapping Screws (not supplied) Mini-Console Video Unit (5) #8 Flat Washers (5) #8x3/4” Self-Tapping Screws Roof Roof Support Headliner 12”x9”x3/4” Plywood Block (4) Self-Tapping Screws (not supplied) Mini-Console Video Unit (5) #8 Flat Washers (5) #8x3/4” Self-Tapping Screws -5 -6- ADV350 Figure A 1) Make the connections to the vehicle for the 12 pin wiring harness. 2) Insert the Circular Mini-Din Connector of the source component harness through the wire tie loop on the main PCB and into the Mini-Din Connector on the main PCB. 3) Pull the wire tie loop tight and cut off the excess. 4) Connect the 12 pin harness to the mating connector on the Video Monitor. 5) Connect power harness to vehicle’s electrical system by tapping into an accessory hot line and a good ground. 6) Verify all functions of the System before final mounting of the finished assembly. 7) Mount and connect the Television antenna. (Optional) Note: A VCP or other A/V Component can be connected to the video monitor system using a second source component harness (purchased separately, part number: 8010730). This harness would plug into the Mini-Din connector on the main PCB as in steps 2 and 3 above. A/V Source Definitions: 1= AV1, VCP or VCP with TV Tuner (Mini-Din on main PCB) 2= AUX-IN (VCP, Game or future DVD etc...) 3= Built-in DVD 4= TV (TV Tuner) TV ANTENNA UNIT (BACK VIEW) To TV Antenna In Red RCA (Audio Right) Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Yellow RCA (Video) White RCA (Audio Left) "Y" Adapter for use with Non-Stereo Installations Item# 5 Power Connector 4 Pin Accessory Harness - Optional Dome Light (P/N:8010730) Power Source CHOKE Auxillary video display 12 VDC Power and Ground INPUT VIDEO (Yellow) Line Out-R (Red) LINE OUT Patch Cord VIDEO RCA-Female RCA Male to Male Line Out-L (White) Line Out-V (Yellow) To Secondary AV Monitor Power Harness Item #3 Power Harness Item #3 OPTIONAL PODTVT *OPTIONAL RELAY BOX TO OPTIONAL ADDITIONAL MONITOR *ANTENNA FOR WIRELESS FM MOD SIRSWB ** See Antenna Note Below *NOTE: If the original relay box P/N SIRSWB is installed, it recommended that the antenna for the wireless FM Modulator be unplugged. See Figure A for antenna location. **N...