Évaluations - 3, GPA: 5 ( )

Fabricant : AMX Taille : 4.48 mb Nom Fichier : Langue d'enseignement:

50 diagrams the RJ-45 pinouts and signals for the Ethernet RJ-45 connector and cable. FIG. 50 RJ-45 wiring diagram VG-Series Modero Touch Panels Installation Procedures: 12" and 15" Panels VG-Series Modero Touch Panels Installation Procedures: 17" Panels Installation Procedures: 17" Panels Overview NXT panels are mounted onto flat (horizontal) surfaces in either a stand-alone or combo (NXT atop an NXABASE/ B battery base) configuration. NXD panels are installed into either a pre-wall surface (using the CBTP17 conduit/wallbox) or a solid surface (using either solid surface or drywall screws). Unpacking the Panel 1. Inspect and confirm the contents of the shipment box to verify that you have all specified parts. Refer to the Specifications section on page 8 for more information about included accessories and other AMX equipment. 2. Carefully remove the panel from the shipping box. 3. Carefully peel the protective plastic cover from the LCD. If the protective plastic LCD cover is not removed, the panel may not respond properly to touch points on the LCD or allow proper screen calibration. Installing the Internal Components Installation of the internal components such as the NXA-PCI80211G Wireless card and NXA-RGB Interface card are described in detail within the following sections: ..Step 2: Install the 802.11g mini-PCI Wireless Card section on page 33. ..Step 3: Install the NXA-RGB Card Component (NXT) section on page 34. Upgrading the Back Box with the MB-TP17 VESA Housing Upgrading the existing back box with the new VESA Mounting Kit (FG033-50) requires 3 main processes: ..Removing the pre-existing back box and installing the new VESA back box. ..Threading cables through the strain relief grommet opening in the rear plastic cover. ..Finalizing the installation of the NXD (with VESA back box and cables) into the plastic cover, securing both components, and finalizing the strain relief grommet installation. The new MB-TP17 Universal VESA Mounting Box uses a standard VESA installation pattern of 75 mm between holes. VESA mounts that conform to this pattern can be used on the MB-TP17 Housing. Removing the Original Modero Back Box 1. Detach all connectors from the side of the touch panel. 2. Remove the magnetic faceplate from the NXD-1700VG unit by gripping the faceplate and pulling outwards while applying a small amount of pressure to remove it from the main unit. 3. Place the LCD face-down on a soft cloth to expose the back of the panel and prevent scratching of the LCD. DO NOT REMOVE THE PANEL SECURING SCREWS. These screws secure the LCD to the metallic casing underneath. 4. Unscrew the Stereo Output nut from the Stereo Output jack. 5. Remove the I/O connector plate by using a grounded Phillips-head screwdriver to remove the two screws and slide the I/O connector plate away from the back box housing. VG-Series Modero Touch Panels Installation Procedures: 17" Panels 6. Remove the four pan-head Housing Screws from the rear of the NXD unit (FIG. 51). These screws secure the back box to the internal panel casing. Unscrew these four Housing Screws to DO NOT these DO NOT REMOVE REMOVE panel securing screws these panel securing screws remove the back box. These make direct contact with the black outer housing. FIG. 51 Location of the attachment screws on the NXD back box DO NOT REMOVE THE FOUR PANEL SECURING SCREWS. These screws secure the LCD to the metallic casing underneath. 7. Lift the back box housing to separate it from the internal panel casing. Installing the MP-TP17 Back Box 1. Unscrew the four pan-head Housing Screws (#8-32) from the MB-TP17 rear plastic cover. 2. Gently place the MB-TP17 back box over the internal panel casing (with the cable routing hole on the right-side of the panel). 3. Re-install and secure the four pan-head Housing Screws into their pre-drilled holes along the edges of the MB-TP17 back box (FIG. 52) and secure them using a grounded Phillips-head screwdriver. 4. Place the I/O connector plate back over the connector opening and align the connector locations. 5. Resecure the I/O connector plate (using a grounded Phillips-head screwdriver) and resecure the Stereo Output nut on the Stereo Output jack. VG-Series Modero Touch Panels Installation Procedures: 17" Panels VG-Series Modero Touch Panels 65 Cable Installation for the MP-TP17 Back Box 1. Connect the cable connectors (RJ-45, Ethernet, and any other audio/video wiring) to their respective locations along the side of the touch panel. 2. Use the tie-wrap (45-0009A) to wrap the cables together inside the VESA Mount enclosure. This cable tie is used to insure the cable will not pull through or work itself through the new larger strain relief grommet (45-0032-01) over time. 3. Thread the incoming cables through the hole on the rear plastic cover and then through the strain relief grommet. 4. Slide the grommet along the cable and securely insert it into the opening on the rear plastic cover (FIG. 52). Finalizing the installation 1. Gently...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :