Évaluations - 4, GPA: 3.8
(
)
)
|
Photos et spécifications Clarion VMA773 |
Facilité d'utilisation
• Do not let the monitor become overheated. If the temperature in the vehicle is high or the monitor has been exposed to direct sunlight, cool the monitor ( such as, by running the air conditioning ) before you turn it on. • Keep all liquids, including beverages and cleaning fluids away from the monitor. Liquids in the monitor can damage the electronics and result in electrical shock or fire . If the unit becomes wet, turn off all power and contact an authorized Clarion dealer to have the monitor inspected. • Never press on the liquid crystal display ( LCD) panel. You may damage it . Failure to observe these precautions may damage your car, the monitor, or the video source, and may void the warranty. 8 Please note • In extremely cold weather the movement of the picture may slow and the picture may darken. The picture will return to normal once the temperature rises. • You may see small black or shiny dots in the liquid crystal panel. These non-conforming pixels are normal and do not indicate a product defect. • Please tear off the liquid crystal panel protect film before using the monitor. The protect film is on the panel’s surface to prevent scratch during transportation. Please remove this film before use. • [And following the provisions of 2004/104/EC Directive. according to paragraph 3.2.9 of Annex I, products meets the limits defined in paragraph 6.5, 6.6, 6.8 and 6.9 of Annex I.] 9 2. USING THE MONITOR 2. USING THE MONITOR These monitors are components in a full audio/video system that may include a VCR, DVD player, game player, camcorder or other video source unit. Note : If you have any questions about compatible components, such as system controllers, source units, FM modulators, or other audio/video products, please contact your authorized Clarion dealer. To operate the monitor, the vehicle ignition key switch must be in the ACC or ON (run) position. ACC or engine ON position WARINING ! To prevent the battery from going dead, always operate this unit with the engine running, if possible . The video source unit ( such as a DVD player) may turn on automatically when you turn the ignition on. 10 Front panel controls Wired Headphone Input Jack IR ( Infrared ) receiver for use with Clarion’s remote controller AV2 Input Jack Increases, decreases or selects , disable the item to be adjusted from menu Adjustment for Tint, Color, Bright, Contrast, Display Mode , Auto Power ON/OFF , and IR Channel, each time this key is being pressed , the select menu goes to the next setting option POWER ON LED IR Lens, IR LED inside to transmit Infrared signals to the headphone Turn on/off the monitor Selects the video sources for AV1 or AV2 11 Wireless headphones ( optional ) Power OFF/ON turns the headphones power on and off. Single channel wireless headphones ( WH143H) are appropriate if only one monitor is installed in the passenger compartment. Configuration 1 Configuration 2 MonitorMonitor Video Source Monitor Video Source Monitor IR CH A IR CH B IR CH A IR CH B Video Source If two monitors are used for rear entertainment systems, dual channel wireless headphones (WH253H) are most appropriate. In this circumstance, channels A and B on both headphone and monitor should be set respectively. Volume adjusts the headphone’s audio volume. Battery compartment requires two AAA 1.5 volt batteries ( not included ) 12 Playing a video or game The monitor is preset at the factory to turn on automatically when you start your car’s ignition. The monitor remains dark until it detects a video signal. 1. Insert the media ( tape , cartridge , game or disc ) into the video source . 2. Turn on the headphones. If this is the first time you’ve used the unit, make sure your wireless headphones have fresh batteries installed. Note : Your wireless headphones must be in view of the monitor for the infrared transmission to work. 3. Press play on the video source. 4. Adjust the volume on your wireless headphone. 13 Display mode setting To choose the proper displaying mode for the different video program sources, please refer to display mode setting as below. 1. Press MENU key until goes to DISPLAY MODE. 2. Press .. (down key ) or ..( up key )to select the displaying mode for : NORMAL, FULL WIDE, WIDE. 3. WIDE may stretch the image to fill the entire screen, NORMAL displays the image at its true aspect ratio (4:3), FULL WIDE stretches the image horizontally to fit the screen for aspect ratio of 16:9. 4 : 3 16 : 9 Notes : • When using a DVD player as the source, make sure that the unit’s output mode is set to “ FULL WIDE “ or “ 16:9 ”. This ensures that the DVD player will generate a video signal which can take advantage of the monitor’s aspect ratio. • When using a source that generates a “ normal “, 4:3 image signal , such as a videogame or videocassette player, the FULL WIDE mode stretches the image to fit the screen. Some minor image distortion may be visible. • Video format are automatically changed for PAL or NTSC depends on video program. ...
Ce manuel est également adapté pour les modèles :Moniteurs - VMA573 (695.19 kb)