Évaluations - 3, GPA: 4
(
)
)
|
Facilité d'utilisation
It is the very effective for touch to maintain steadily for a time in specified area. This function is for banking and industrial control applications, such as ATM, Switches of industrial equipment and used in both Click on touch and Click on Release modes. The "Delay Touch Setting" properties can be set selectively. The higher the value (unit:millisecond), the longer the touch-delay time; "area" is utilized to regulate the effective area in which finger maintains on the touch plane. The higher the value (unit: pixel), the wider the effective area. 9. Prevent System to Standby Unable (default); this function may prevent System from Standby. When the IR touchscreen is provided with serial ports as a simple output device, the function may enable recovery out of the state of automatic system standby. 10. Drag Delay The function show the amount of millisecond "Drag Delay" will take to be enabled after you click that. Drag Delay may be adjusted to the correct value if the object can not be precisely selected or if jitter happens to cursor when you touch. The unit is millisecond. 11. False touch rejection The snow and rain drop will be mistakenly a single touch. So the function of "False touch rejection" may be selected in driver to avoid the above error without the normal manipulation. The function of "Enable Delay Touch" will do the work to prevent the false touch. Instructions see Attachment : Setting of touchscreen in strong light, rain and snow condition. Serial port Settings 1. Installation of the driver of serial port finished, choose "start" - "All Programs" - "IRTOUCHSYSTEMS" - "Serial Port Settings". In the list show both the name of IR touch device installed and the number of the serial ports. You may choose [Install] when some serial ports are available or choose [Remove] to uninstall the driver if you don't want to use the touchscreen. 2. Click [Change Port] to set and change setting of the selected Serial Port. Attachment The general setting of touchscreen Select "Mouse Emulation" mode, then choose "Enable Touch" Send Right ClickEnable DoubleClick. In general functions of Enable Delay Touch and False touch rejection may not selected to avoidslowing the touch response. It is proved null if you quickly click or drag the touch point. Installment 1. Send Right Click To enable right-click function (default). Click and press on any area on the screen for two second, the right-click menu will popup. Right-click is only available in Mouse Emulation mode. The “Delay” value is 1000(1second); The “Area” value is set to 32px at optimum. 2. Enable Double Click Same as the function of Mouse Double Click. Double click on the same setting area of objects in a short time may open up the object. "Speed" unit is at 500 to 550. "Area" unit is 32px. 3. Drag Delay The function show the amount of millisecond "Drag Delay" will take to be enabled after you click that. Drag Delay may be adjuste d to the correct value if theobject can not be precisely selected or if jitter happens to cursor when you touch. The unit is millisecond. Setting of touchscreen in strong light, rain and snow condition Specification 1. Each value should be gradually set in "Delay Touch Settings" after fulfillment of "Enable Delay Touch". "Delay" is set to 40 and "Area" to 16. 2. Enter count It means how many times you click to approach the setting value within 3 seconds. Then driver will install the function of "False touch rejection" where quick click or scratch will be considered void except the touch point on the active area for quite a while. 3. Leave count "False touch rejection" is no longer effective when the click times within 5 seconds is less than the setting number. Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix Select Language Main Page Model The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement. Adjusting the LCD Display Input Available Modes PC / BNC / DVI AV S-Video Component HDMI MagicInfo Source List [MENU] > [ENTER] > [ENTER] > [. / .] > [ENTER] Use to select PC, BNC, or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1) PC 2) BNC 3) DVI 4) AV 5) S-Video 6) Component 7) HDMI 8) MagicInfo [The direct button on the remote control is the 'SOURCE' button.] Note • PIP turns off when the LCD Display is switched to an external source. • For PC and DVI, this is deactivated if the cable is disconnected. PIP When external AV devices such as VCRs or DVDs are connected to the LCD Display , PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off/On) Note • More than one PIP cannot be overlapped on screen as BNC and the component use the same terminal. 1) PIP [MENU] > [ENTER] > [. / .] > [ENTER] > [ENTER] > [. / .] > [EN...
Ce manuel est également adapté pour les modèles :Moniteurs - 700TSN (3.74 mb)