|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Look down at the screen and face the screen forwards. Maintain the correct posture when using this product. Adjust the angle of the product so that light is not reflected onto the screen. Keep your elbow at a right angle and keep your arm level with the back of your hand. Keep your elbow at a right angle. Place your heels flat on the ground while keeping your knees at an angle of 90 degrees or higher and maintain the position of your arm so that your arm is below your heart. 1-3 Major Safety Precautions 2 Installing the Product 2-1 Package Contents S3 • Unpack the product and check if all of the following contents have been included. • Store the packaging box in case you need to move the Product at a later stage. Monitor CONTENTS O & ieo ^7 Installation Manual Product Warranty User Manual D-Sub Cable (Not available in all locations) (Not available in all locations) \ — Power Cord Cleaning Cloth Stand Connector Stand OPTIONAL PARTS HDMI Cable DVI Cable E3 The cleaning cloth is supplied with black high-glossy models only. Installing the Product 2-1 2-2 Installing the Stand @ Before assembling the product, place the product down on a flat and stable surface so that the screen is facing downwards. Insert the Stand Connector into the Stand in the direction shown by the figure. Check if the Stand Connector is firmly connected. Turn the connecting screw at the bottom of the stand fully so that it is completely fixed. Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product is facing downwards. Hold the main body of the product with your hand as shown by the figure. Push the assembled stand into the main body in the direction of the arrow as shown in the figure. 2-2 Installing the Product Installing the Product 2-2 2-3 Removing the Stand @ Before removing the stand, place the product down on a flat and stable surface so that the screen faces downwards. Place a soft cloth over the table to protect the product and place the product onto the cloth so that the front of the product faces downwards. Hold the main body of the product with your hand as shown by the figure. Pull the stand in the direction of the arrow as shown in the figure to separate it. Turn the connecting screw at the bottom of the stand to separate it. Take the Stand Connector out of the Stand by pulling it in the direction of the arrow as shown in the figure. 2-3 Installing the Product 2-4 Installing the Stand for the Wall Mount This product provides a stand mount of 75 mm x 75 mm(3.0 x 3.0 inches) that complies with the VESA specifications. ii3 Stand Mount Stand (Optional) 1. Turn the product off and unplug the power cord from the wall outlet. 2. Place a soft cloth or cushion on a flat surface to protect the panel and place the product down on the cloth so that the front of the product faces downwards. 3. Separate the stand. 4. Align the groove of the part of the product that is to be connected to the stand with the groove in the stand (desk-top stand, wall mount stand or another stand) and firmly fix the stand by fastening the screw. D • If you use a screw that is longer than the standard specifications, the inside of the product may be damaged. • For wall mounts that are not compatible with the standard VESA specifications, the length of the screw may differ depending on the corresponding specifications. • Do not use screws that are incompatible with the standard VESA specifications and do not assemble them using excessive force. This may result in damage to the product or injury due to the product falling. The company shall not be held liable for any damage or injury. • The company shall not be held liable for any damage to the product or injury caused by using a stand that is not compatible with the specified specifications or due to an installation not performed by an authorized installation engineer. • When installing the product using a wall mount, purchase a wall mount that provides at least 10 cm of space from the wall. • The company shall not be held liable for any problems caused by using a stand that is not compatible with the specified specifications. • Use the wall mount according to the international specifications. Installing the Product 2-4 2-5 Connecting with a PC ¡3 The connecting part may differ depending on the product model. 1. Connect the product to a PC depending on the video output supported by the PC. • When the graphics card provides D-Sub (
Moniteurs - B2230H (961.35 kb)
Moniteurs - B2330 (961.35 kb)
Moniteurs - B2430H (961.35 kb)