Évaluations - 4, GPA: 3.8
(
)
)
|
Photos et spécifications Samsung C23A750X |
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
.. To charge the battery of a device, be sure to connect the device to the blue USB 3.0 port on the left side of the product. .. Battery charging is available in power-saving mode, but not available when the product is powered off. .. Note that the battery will not be charged if the power cable is disconnected from the power socket. Connect multiple source devices to the product and use the device you want by changing the input source. 2.4.2 Connecting to a LAN "HUB Monitor" allows you to use the Internet from a PC when you connect a LAN cable to the product (if the product is connected to the PC), without having to connect the LAN cable directly to the PC. Wlreless USB USB3.0 CABLE Wlreless USB USB3.0 CABLE 36 2 Using "HUB Monitor" 2 Using "HUB Monitor" This is achieved by an internal chip that transmits data received via the LAN cable to the PC as a converted USB signal. Connecting to a LAN via Wireless USB Connecting to a LAN via USB cable This product cannot connect to multiple source PCs at the same time and vice versa. 2.5 Configuring the HUB Monitor IP 1 After installing the integrated driver for HUB Monitors, go to Control Panel Network and Internet Network and Sharing Center Change adapter settings. 2 You can see that the following two devices are displayed. a. The user PC’s network device b. The HUB Monitor’s network device (USB to Ethernet adapter) The two devices above refer to your PC’s LAN network device and your HUB Monitor’s network device. To use the Internet using the HUB Monitor’s LAN network, configure the network settings as follows according to the type of IP you will be using. 2.5.1 Dynamic IP The dynamic IP address mode automatically configures the network settings on the PC using data sent by a server, which allots an IP address. This is possible, owing to the “DHCP (Dynamic Host Configuration Protocol)” service. The service consists of three steps: an IP address allotment request is sent to the DHCP server when the PC boots up, the DHCP server that received the request transmits LAN LAN USB CABLE .... .... .... 37 2 Using "HUB Monitor" 2 Using "HUB Monitor" network information such as the IP address to the PC, and the transmitted network information is automatically registered to the network settings on the PC. The DHCP service is convenient and useful especially in an environment where multiple PCs are used. Theoretically, the IP address changes each time the PC boots up (or an IP allotment request is sent); in many cases, however, the existing IP address is re-allotted. An Internet router performs two roles: creating a private IP address (NAT service) and automatically allotting the IP address to each PC (DHCP service) at the same time. When using your HUB Monitor’s or notebook PC’s LAN network, ensure you insert a LAN cable into only one device. Otherwise, a system crash may occur. Dynamic IP User 1 To use a dynamic IP address, connect a LAN to your HUB Monitor. 2 Next, go to the network settings menu and activate the HUB Monitor’s network device (select “Use”). Go to Control Panel Network and Internet Network and Sharing Center Change adapter settings. Next, right-click on the HUB Monitor’s network device (marked “LAN9512/ LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”) and select Use. 3 Using the network properties menu, check that the IP address mode for the HUB Monitor’s network device is set to Auto. Go to Control Panel Network and Internet Network and Sharing Center Change adapter settings. Next, right-click on the HUB Monitor’s network device (marked “LAN9512/ LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”). .... .... .... .... .... .... 38 2 Using "HUB Monitor" 2 Using "HUB Monitor" Select Properties Internet Protocol Version 4 (TCP/IPv4) Properties. 2.5.2 Static IP To configure the IP address (private or official) on your PC, someone (mostly a server system) must distribute and allot an IP address to the PC. An official IP address is allotted by your Internet service provider, and a private IP address is allotted by your Internet router. You can select whether to configure the IP address on the PC automatically or manually. The static IP address mode is used to manually enter an IP address. The static IP address mode is suitable if the IP address for the PC should not be changed (such as for a file sharing server) and generally is not used, except under such special circumstances. When using your HUB Monitor’s or notebook PC’s LAN network, ensure you insert a LAN cable into only one device. Otherwise, a system crash may occur. Static IP User 1 Set the LAN network for the notebook PC to Disable. 2 Go to Control Panel Network and Internet Network and Sharing Center Change adapter settings. Next, right-click on the notebook PC’s network device and select Disable. 3 Right-click on the HUB Monitor’s network device (marked “LAN9512/LAN9514 USB 2.0 to Ethernet 10/100 Adapter #7”), and select Use. Be sure to perform this process before configuring the IP. 4 Configure the static...
Ce manuel est également adapté pour les modèles :Moniteurs - C27A750X (8.04 mb)