Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
yyDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. CAUTION Detaching the Stand Base 1 Place the Monitor set with the screen side down on a flat and cushioned surface. 2 Stand Base Stand Base Stand Body Stand Body Pull out the Stand Body and Stand Base from the monitor set. Turn the screw to the left with a coin. Pull out the Stand Base. 1 2 3 6 ENEGNLGISH ASSEMBLING AND PREPARING Mounting on a table 1 Lift and tilt the Monitor set into its upright position on a table. Leave a 10 cm (minimum) space from the wall for proper ventilation. Using the cable holder 2 Connect the AC-DC Adapter and Power Cord to a wall outlet. 3 Press (Power) button on the bottom switch panel to turn the power on. 10 cm 10 cm 10 cm 10 cm Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur. CAUTION Cable holder or ASSEMBLING AND PREPARING 7 Using the Kensington security system When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers. Do not touch or press the screen when adjusting the angle of the monitor. Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body. WARNING Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view. NOTE Front Rear The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit Connect the Kensington security system cable between the Monitor set and a table. The Kensington security system is optional. You can obtain it from most electronics stores. NOTE ENGENGLISH ASSEMBLING AND PREPARING 8 ENGENGLISH Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. 10 cm 10 cm 10 cm 10 cm If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop. 1 Please, Use the screw and wall mount interface in accordance with VESA Standards. 2 If you use screw longer than standard, the monitor might be damaged internally. 3 If you use improper screw, the product might be damaged and drop from mounted position. In this case, LG Electronics is not responsible for it. 4 VESA compatible. 5 Please use VESA standard as below. • 784.8 mm (30.9 inch) and under * Wall Mount Pad Thickness : 2.6 mm * Screw : . 4.0 mm x Pitch 0.7 mm x Length 10 mm • 787.4 mm (31.0 inch) and above * Please use VESA standard wall mount pad and screws. Model E1942S E2042S E2242S E2042T E2242T E2342T E2442T VESA (A x B) 75 x 75 100 x 100 Standard screw M4 Number of screws 4 yDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur. yIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury. yUse only an authorized LG wall mount and contact the local dealer or qualified personnel. yDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty. yUse only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty. CAUTION NOTE • Use the screws that are listed on the VESA standard screw specifications. • The wall mount kit will include an installation manual and necessary parts. • The wall mount bracket is optional. You can obtain additional accessories from your local dealer. • The length of screws may differ depending on the wall mount. Be sure to use the proper length. • For more information, refer to the instructions supplied with the wall mount. USING THE MONITOR SET 9 USING THE MONITOR SET Connecting to a PC • Your Monitor set supports Plug & Play*. *Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention. D-SUB connection Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations. ENGENGLISH yMac adapter For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector. yWhen using a D-Sub signal input cable connector for Macintosh NOTE DVI-D connection Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations. 10 USING THE MONITOR S...
Ce manuel est également adapté pour les modèles :Moniteurs - E1942S (2.64 mb)
Moniteurs - E1942S-BN (2.64 mb)
Moniteurs - E2042S-BN (2.64 mb)
Moniteurs - E2242T (2.64 mb)