Évaluations - 2, GPA: 3
(
)
)
|
Par ce dispositif a également d'autres instructions :
Facilité d'utilisation
Connecting the stand (B type) 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Hinge Body Stand Body Stand Body 4. Once assembled take the monitor up carefully and face the front side. Stand Base Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 7 Connecting the Display Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on the surface. cushion or soft cloth. 3.Nip Latch inside,Take off the stand base from stand body. 8 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand (C type) 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. Stand Body Hinge Body Stand Body Stand Base 4. Turn the screw to the right to fix the Stand Body to the Stand Base. Screw Turn the screw by using the screw handle. 5. Once assembled take the monitor up carefully and face the front side. Important This illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot. 9 Connecting the Display Connecting the Display Disassembling the stand 1. Put a cushion or soft cloth on aflat 2. Place the monitor face Down on the surface. cushion or soft cloth. 3.To disconnect the Stand Base from the Stand Body,simply unfold the screw handle and turn"counter-clockwise" to loosen the screw and disconnect the Stand Base from its body. 10 Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5° to 15° ERGONOMIC It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees. Do not touch or press the screen when adjusting the angle of the monitor. When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s). 11 Connecting the Display E1941T/E2041T/E2241T/E2341T/E2441T Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable 1 and power cord 2 in order, then tighten the screw of the signal cable. Connect DVI-D(Digital signal) Cable Connect D-sub(Analog signal) Cable A B Wall-outlet type Mac adapter : For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-sub VGA connector on the supplied cable to a 15 pin 2 row connector. When using a D-Sub signal input cable connector for Macintosh Varies according to model. NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the view as shown. 3. Press the power button on the front panel to turn the power on. When monitor power is turned on, the 'Self Image Setting Function' (Only Analog Mode) Power Button Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure. NOTE ‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals. ‘AUTO’ Function? When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. 12 Connecting the Display E1941S/E2041S/E2241S Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable 1 and power cord 2 in order, then tighten the screw of the signal cable. A Connect D-sub(Analog signal) Cable Wall-outlet type Mac adapter : For Apple Macintosh us...
Ce manuel est également adapté pour les modèles :Moniteurs - E2341T (3.92 mb)