Évaluations - 0, GPA: 0 ( )

Fabricant : Philips Taille : 3.16 mb Nom Fichier : Langue d'enseignement:

[Application] 1 When application is [Hospitality], the following are activated. Last status is disabled.• Limited Consumer menu: When • in Professional mode, the guest can display the Consumer menu to adjust TV parameters. However, these settings will not be stored in TV memory. TV lock and parental ratings (except • Sleep timer) are disabled. Entry into service mode is disabled • in order to prevent the guest from changing service settings. 2 When application is [Signage], the below functions behave as per normal consumer. Last status is enabled.• The full TV menu can be accessed and • changes are stored in TV memory. TV lock and parental ratings are • enabled. Entry into service mode is enabled.• Note ••The default application for TV should be [Hospitality], while that for monitor should be [Signage]. [Consumer setup] A shortcut to enter the full TV menu. This allows the installers to do all the TV setup settings. Note Selects ••[PBS settings] > [Store] to save the changes in the [Consumer setup menu]. [Smartloader / USB to TV] Loads the TV configuration data (including the video, audio, channel Table, and Professional mode settings) from a Smartloader / USB device to the TV set. [TV to Smartloader / USB] Loads the TV configuration data (including the video, audio, channel Table, and Professional mode settings) from the TV set to a Smartloader /USB device. [Store] Selects [Confirm] to store Professional mode settings. Note After storing the settings, refer to page 29 “Low power standby (Green / Fast)”: When • [Fast] is selected, you need to restart the TV mains power for the changes in Professional mode to take effect. When • [Green] is selected, you need to switch the TV from standby to on again for the changes in Professional mode to take effect. [Reset] Selects [Yes] to reset all settings in Professional mode to factory default. Switch on settings [Maximum volume] This option specifies the maximum allowable volume level of the TV. [Switch on picture format] Sets available picture format when the TV is switched on. Note If the picture format is not supported •• with the activated source, [Auto format] detection is applied. [Low power standby (Green / Fast)] Defines the power mode when TV enters to standby by pressing remote control power button or TV local power button. [Fast]: • When set, the TV will enter semi- standby mode to achieve fast powering up. [Green]: • When set, the TV will enter low standby power mode to achieve minimum power consumption. [Power on] The power on function allows the TV to enter a specific mode ([On], [Standby], or [Last status]) of operation after the mains power is activated. [On]: • When set, the TV will always turn on after the mains power is activated. [Standby]: • When set, the TV will always turn to standby after the mains power is activated. [Last status]:• When set, the TV will always turn to the last status (either On or Standby) whenever the mains power is activated. [Smart power] Adjusts the picture backlight to achieve the following power saving mode. [Off]: • Smart power is disabled. ( Vivid mode is applied). [Low]: • The picture backlight is at low power saving mode. (Movie mode is applied). [Medium]: • The picture backlight is at medium power saving mode. (Standard mode is applied). [High]: • The picture backlight is at high power savings (Energy saving mode is applied). [Display message] [Off]: • Disables the display of the welcome message. [On]: • Enables the display of the welcome message for a pre-defined time after the TV turns on from standby or off. Note ••Selects [Welcome message] . [Message time-out] to set the period of time to display the welcome message. [Set ID] (Only available in [Signage] mode). This function allows installer to designate a serial ID number for each TV. Through the ID number, the installer can control each TV by using RS232-device-chaining. Switch on volume When the guest switches the TV on, it will play at the specified volume level. [Last status]• : If [On] is selected, the TV will be automatically switched to the last volume status whenever the mains power is turned on. (The volume level can not exceed the [Maximum volume] level). [User defined]• : (Only appears when you select [Last status] . [Off]. )The guest can adjust his/her preferred switch on volume level. Switch on channel When the guest switches the TV on, it will play at the specified channel. [Last status]• : If [On] is selected, the TV will be automatically switched to the last channel status whenever the mains power is turned on. [User defined]• : (Only appears when you select [Last status] . [Off]). The guest can choose his/her preferred switch on channel. Welcome message The Welcome message function allows the TV to show a customized greeting to the hotel guest whenever the TV is switched on. This helps to personalize the hotel experience for guests. The Welcome message can consist of 2 lines of text, with each line containing a maximum of 20 alphanumeric char...

Téléchargez votre

Pour télécharger, entrez 2 chiffres :