Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
RETURN TO TOP OF THE PAGE Technical Specifications* CRT • Size and deflection 17 inch / 41 cm ; 90° deflection angle • Dot pitch 0.25 mm • Horizontal pitch 0.21 mm • Tube type Shadow mask, Real Flat, high contrast, anti-glare, anti-static, anti reflection, light transmission 50% • Phosphor P22 • Recommended display area 12.0" x 9.0" / 306 x 230 mm • Maximum display area 12.8" x 9.6" / 325 x 244 mm SCANNING • Horizontal scanning 30 - 71 KHz • Vertical scanning 50 - 160 Hz VIDEO • Video dot rate 108 MHz • Input impedance - Video 75 ohm - Sync 2.2 kOhm • Input signal levels 0.7 Vpp • Sync input signal Separate sync Composite sync • Sync polarities Positive and negative WHITE COLOR TEMPERATURE Chromaticity CIE coordinates: • at 9300 degrees K x = 0.283 / y = 0.297 • at 6500 degrees K x = 0.313 / y = 0.329 • at sRGB x = 0.313 / y = 0.329 sRGB sRGB is a standard for ensuring correct exchange of colors between different devices (e.g. digital cameras, monitors, printers, scanners, etc.) Using a standard unified color space, sRGB will help represent pictures taken by an sRGB compatible device correctly on your sRGB enabled Philips monitors. In that way, the colors are calibrated and you can rely on the correctness of the colors shown on your screen. Important with the use of sRGB is that the brightness and contrast of your monitor is fixed to a predefined setting as well as the color gamut. Therefore it is important to select the sRGB setting in the monitor's OSD. To do so, open the OSD by pressing the OK button on the front of your monitor. Use the down button to go to Color temperature and press OK again. Then move the down button to go to sRGB and press OK again. Exit this OSD. After this, please don't change the brightness or contrast setting of your monitor. If you change either of these, the monitor will exit the sRGB mode and go to a color temperature setting of 6500K. For more information on sRGB, please visit: * These information are subject to change without notice. RETURN TO TOP OF THE PAGE Automatic Power Saving If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. And if an input from a keyboard, mouse or other input device is detected, the monitor will automatically "wake up". The following table shows the power consumption and signaling of this automatic power saving features: Power Management Definition VESA's Mode Video H-sync V-sync Power Used Power Saving (%) LED color ON Active Yes Yes Typical 68 W 0 % Green OFF Blanked No No < 2W 96% Yellow This monitor is ENERGY STAR® compliant. As an ENERGY STAR® Partner, PHILIPS has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimensions 15.7" x 16.1" x 16.5" / 399 x 410 x 419 mm (including base) 15.7" x 14.7" x 16.5" / 399 x 373 x 419 mm (excluding base) • Weight 16.5 kg • Power supply 90 - 264 VAC, 50/60Hz • Temperature (operating) 0° to 40°C / 32° to 104°F • Temperature (storage) -25° to +65°C / -13° to +149°F • Relative humidity(storage) 5% to 95% * Resolution 1280 x 1024, standard size, contrast max., brightness 50%, 9300°, full white pattern. * These information are subject to change without notice. RETURN TO TOP OF THE PAGE Pin Assignment The 15-pin D-sub connector (male) of the signal cable (IBM systems): Pin No. Assignment Pin No. Assignment 1 Red video input 9 No pin 2 Green video input 10 Logic ground 3 Blue video input 11 Identical output - connected to pin 10 4 Identical output - connected to pin 10 12 Serial data line (SDA) 5 Ground 13 H. Sync / H+V 6 Red video ground 14 V. Sync (VCLK for DDC) 7 Green video ground 15 Data clock line (SCL) 8 Blue video ground RETURN TO TOP OF THE PAGE Views Follow the links to see various views of the monitor and its components. Front View Rear View RETURN TO TOP OF THE PAGE Installing your Monitor Front View • Rear View • 6G3B11 Multimedia Base (option) • PCUH411 USB Hub (option) Front View Power button switches your monitor on. OK button which when pressed will take you to the OSD controls Contrast hotkey. When the UP arrow is pressed, the adjustment controls for the CONTRAST will show up. UP and DOWN buttons are used when adjusting the OSD of your monitor Brightness hotkey. When the RIGHT arrow is pressed, the adjustment controls for BRIGHTNESS will show up. LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. RETURN TO TOP OF THE PAGE Rear View 1. Power in - attach power cable here. Video In - this is a cable which is already attached to your monitor. Connect the other end of the cable to your PC. 2. RETURN TO TOP OF THE PAGE On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips monitors which allows an end-user to ad...
Ce manuel est également adapté pour les modèles :Moniteurs - 107T4174 (689.75 kb)