Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
How do I correct this? l If the OSD menu is also missing a color, please contact service for details l Set color temperature to 9300 color coordination l Check the video cable for any bent pins l Video card could be defective (try the monitor with another computer). 41. When I degauss my monitor, it makes a loud noise. Is this normal? Yes, when degaussing your monitor via the OSD, it is normal for the monitor to make a relatively loud noise. Please be aware that many models will not degauss more than once within any given time period (up to 10 minutes). This is due to the unit having a temperature sensitive resistor. While the unit is degaussing, the resistor increases in value with heat and once it reaches a certain temperature, the resistance will rise and prevent voltage from reaching the degaussing coil. This is what stops the degausser, and this device's resistance will decrease as it cools back off, enabling the degauss function to operate again. This is an intentional design and is an industry standard, not just for Philips monitors. Please be aware that not all models in the Philips range has this manual degauss function. Some models are built with an auto degauss feature which automatically degausses the monitor when it is switched on. 42. How do I adjust the picture on the screen? Please perform the following to correct the picture image: l Reset your monitor via the OSD menu l Adjust the Horz (width) and/or Vert size (height) in the OSD l Change monitor timing to work at the recommended resolution 43. The edge of the picture on the screen appears to be distorted. How can I correct this? Please perform the following to correct the picture image: A magnetic or electrical interference typically causes poor geometry in the picture. Place the monitor in a different physical location l l Reset the monitor to the factory preset via the OSD menu l Access the Geometry Menu in the OSD of the Monitor and perform the necessary adjustments l Change the monitor timing to the recommended resolution 44. The picture appears too dim. How can I correct this? Adjust Brightness and/or Contrast via the monitor 's OSD. Some models have a Video Input Select under Advanced Controls in the monitor 's OSD. Most computers require it to be set at 0.7V. Please review the following for possible solutions: l If the OSD menu is also dim, please contact service for repair l Reset the monitor via the OSD menu l Change the color temperature settings to 9300 color coordination via the OSD menu l Set the Contrast to maximum level (100) and Brightness to middle level (50) Video card could be defective (try the monitor with another computer) 45. I have noticed two thin horizontal lines on the screen of my Philips monitor. Is this normal? This phenomenon can occur with Philips 107P, 109P and 201P monitors and is normal. Your monitor is using an Aperture Grille, which consists of fine vertical wires to align the electron beams with the phosphors on the screen. To prevent these vertical wires from vibrating and to keep them properly aligned with the picture tube, two horizontal damper wires are required. These are located on one-third and on two-third from the top of the screen. The result is that you will see two very thin horizontal lines over your screen since the two wires are casting a slight shadow on the screen surface. You will find these wires (line) in any monitor from Philips and other brands using the Aperture Grille technology. 46. How can I increase the color display of my monitor? The amount of video memory your video card holds determines the amount of colors that can be displayed on your computer screen. To get the most out of your video card, you will need to either install the latest drivers onto your computer or upgrade the video cards memory. Please check with your computer or video card manufacturer for further details. 47. Why is there no picture on my monitor? l Check the wall socket for power. Verify that there is power by connecting another product. l Ensure the power cable is correctly attached to both the wall socket and the monitor. l Check that the power button is switched on. l Unplug the monitor for approx. 1 minute and plug it in again. Switch the monitor back on. 48. Why is there no picture on my monitor even though the power LED is yellow/amber? Reboot your computer while holding the Ctrl key on your computer. If you see any picture during the boot procedure, please verify the settings of your video card (for Windows go to Control Panel and select Display). l Check that the video cable is not damaged, bent or that any of the pins in the connector are damaged (please be aware that all VGA connectors have one missing pin). If damaged, replace with a new cable. l l Check that the cable is attached correctly to the computer. l Press any key on the keyboard to wake-up the computer from power saving mode. 49. Why is there no picture on my monitor even though the power LED is green? Verify the Contrast and Brig...