Évaluations - 0, GPA: 0
(
)
)
|
Facilité d'utilisation
CAUTION yyLay a foam mat or soft protective cloth on the surface to protect the screen from damage. yyWhen attaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. CAUTION Tighten the screws firmly to prevent the TV from tilting forward. Do not over tighten. 2 Attach the Stand Body from the TV. CAUTION yyDo not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury. yyThe illustration shows a general example of installation and may look different from the actual product. yyDo not carry the monitor upside-down by holding the stand body as this may cause it to fall off, resulting in damage or injury. yyThe illustration shows a general example of installation and may look different from the actual product. 3 Secure the TV and the Stand Body with the 2 screws. 26MA33D 29MN33D 26MA33V 29MN33V If you are not mounting the TV to a wall, use the following instructions to attach the stand. 1 Place the TV with the screen side down on a flat and cushioned surface. WARNING If you don`t fasten the screw tightly, TV will fall down and get damaged. 4 Attach the Stand Base from the Stand Body by turning the screw to the right with a Coin. 2 Attach the Stand Body from the TV. Insert the two Lockers of the Stand Body right into the groove of the TV head and secure them by pressing the left and right bottom sides. Locker CAUTION Tighten the screws firmly to prevent the TV from tilting forward. Do not over tighten. CAUTION yyDo not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury. yyThe illustration shows a general example of installation and may look different from the actual product. yyDo not carry the monitor upside-down by holding the stand body as this may cause it to fall off, resulting in damage or injury. yyThe illustration shows a general example of installation and may look different from the actual product. Mounting on a table 1 Lift and tilt the TV into its upright position on a table. Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. 2 Connect the AC-DC Adapter and Power Cord to a wall outlet. 10 cm 10 cm 10 cm 10 cm or WARNING When you adjust the angle, do not hold the buttom of the TV frame as shown on the following illustration, as may injure your fingers. CAUTION CAUTION Disconnect the power cord first, and then move or install the TV. Otherwise electric shock may occur. Do not place the TV near or on sources of heat, as this may result in fire or other damage. Using the Kensington security system NOTE Tilt from +20 to -5 degrees up or down to adjust the angle of the TV to suit your view. The Kensington security system connector is located at the back of the TV. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit Connect the Kensington security system cable between the TV and a table. +20-5 Front Rear Tidying cables Gather and bind the cables with the supplied cable tie. NOTE The Kensington security system is optional. You can obtain additional accessories from most electronics stores. 3 Pull out the Stand Body from the TV. Detaching the Stand 24MN33D 22MA33D 22MA33V 24MN33V 1 Place the TV with the screen side down on a flat and cushioned surface. CAUTION yyLay a foam mat or soft protective cloth on the surface to protect the screen from damage. yyWhen detaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. 2 Turn the screw to the left, and then pull out the Stand Base from the Stand Body. 3 Remove 2 screws and pull out the Stand Body from the TV. 26MA33D 29MN33D 29MN33V 26MA33V 1 Place the TV with the screen side down on a flat and cushioned surface. CAUTION yyLay a foam mat or soft protective cloth on the surface to protect the screen from damage. yyWhen detaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. 2 Turn the screw to the left, and then pull out the Stand Base from the Stand Body. Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide. VESA (A x B) 100 x 100 Standard screw M4 Number of screws 4 Wall mount bracket (optional) RW120 ...
Ce manuel est également adapté pour les modèles :Moniteurs - 24MN33D-PR (3.31 mb)
Moniteurs - 24MN33D-PZ (3.31 mb)
Moniteurs - 26MA33D (3.31 mb)
Moniteurs - 26MA33D-PZ (3.31 mb)