Évaluations - 0, GPA: 0
(
)
)
|
Photos et spécifications LG 23MA73D |
Facilité d'utilisation
Connection to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)” When applying the RF Isolator, a slight loss of signal sensitivity can occur. Parts and buttons Remote Control Sensor Standby Light yyLighting On : When Power is turned off yyLighting Off : When Power is turned on Touch Buttons NOTE All of the buttons are touch sensitive and can be operated through simple touch with your finger. Power and control touch button are located on the bottom. Touch button Description Scrolls through the saved programmes. Adjusts the volume level. OK Selects the highlighted menu option or confirms an input. SETTINGS Accesses the main menus, or saves your input and exits the menus. INPUT Changes the input source. / I Turns the power on or off. (PC) AV 1AV 2 IN(MONO) Connection panel (See p.20) Lifting and moving the TV When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for save transportation regardless of its type and size. Avoid touching the screen at all times, as this may result in damage to the screen or some of the pixels used to create images. CAUTION yyIt is recommended to move the TV in the box or packing material that the TV originally came in. yyBefore moving or lifting the TV, disconnect the power cord and all cables. yyHold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area. yyWhen holding the TV, the screen should face away from you to prevent the screen from scratches. yyWhen transporting the TV, do not expose the TV to jolts or excessive vibration. yyWhen transporting the TV, keep the TV upright, never turn the TV on its side, or tilt towards the left or right. Setting up the TV Attaching the Stand If you are not mounting the TV to a wall, use the following instructions to attach the stand. 1 Place the TV with the screen side down on a flat and cushioned surface. 2 Attach the Stand Base from the Stand Body by turning the screw to the right with a Coin. CAUTION CAUTION yyLay a foam mat or soft protective cloth on the surface to protect the screen from damage. yyWhen attaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. Tighten the screws firmly to prevent the TV from tilting forward. Do not over tighten. 3 Attach the Stand Body from the TV. CAUTION yyDo not carry the monitor upside-down as this may cause it to fall off its stand, resulting in damage or injury. yyThe illustration shows a general example of installation and may look different from the actual product. yyDo not carry the monitor upside-down by holding the stand body as this may cause it to fall off, resulting in damage or injury. yyThe illustration shows a general example of installation and may look different from the actual product. 2 Connect the AC-DC Adapter and Power Cord to a wall outlet. Mounting on a table 1 Lift and tilt the TV into its upright position on a table. Leave a 10 cm (4 inches) (minimum) space from the wall for proper ventilation. 10 cm 10 cm 10 cm 10 cm CAUTION Do not place the TV near or on sources of heat, as this may result in fire or other damage. WARNING NOTE When you adjust the angle, do not hold the buttom of the TV frame as shown on the following illustration, as may injure your fingers. Tilt from +20 to -5 degrees up or down to adjust the angle of the TV to suit your view. +20-5 Rear Front CAUTION Disconnect the power cord first, and then move or install the TV. Otherwise electric shock may occur. Using the Kensington security system Tidying cables The Kensington security system connector is located at the back of the TV. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit Connect the Kensington security system cable between the TV and a table. 1 Attach the cable holder to the edge of stand body securely. 2 Gather and bind the cables with the supplied cable holder. NOTE The Kensington security system is optional. You can obtain additional accessories from most electronics stores. CAUTION After attachment, if the cable holder is pulled with excessive force, it may fall off. Detaching the Stand 1 Place the TV with the screen side down on a flat and cushioned surface. 3 Turn the screw to the left, and then pull out the Stand Base from the Stand Body. CAUTION yyLay a foam mat or soft protective cloth on the surface to protect the screen from damage. yyWhen detaching the stand to the TV, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches. 2 Pull out the Stand Body from the TV. Mounting on a wall For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed installation instructions are available from your dealer, see the ...
Ce manuel est également adapté pour les modèles :Moniteurs - 23MA73D-PZ (2.79 mb)
Moniteurs - 27MA73D (2.79 mb)
Moniteurs - 27MA73D-PZ (2.79 mb)