Évaluations - 1, GPA: 3
(
)
)
|
Facilité d'utilisation
You should read the instructions in CD-ROM Disk Touchscreen section carefully before you attempt installation. The FPM-3150G-XCE, RCE need to install Penmount 6000 driver. Please find Penmount 6000 folder and install the driver into your system. Note 1: The driver manual are examples only. You must follow the flow chart instructions and pay attention to the instructions which then appear on your screen. Note 2: The USB & RS-232 cable not allow to connect to system at the same time. Note 3: USB & RS-232 interface driver is different, uninstall previous driver before installing a different driver. ■Note 4: If there is any others OS driver need, could download at the web site: (Penmount 6000) FPM-3150 Series User Manual 16 LU B Setting Serial Data for Expansion Appendix B Setting Serial Data for Expansion B.1 Setting Serial Data for Expansion The twelve kinds of timings below are already programmed in this module. The input synchronous signals are automatically recognized. Resolution Vertical Frequencies 56 Hz 60 Hz 70 Hz 72 Hz 75 Hz Pass Fail Pass Fail Pass Fail Pass Fail Pass Fail 640 x 480 V V V 800 x 600 V V V V V 1024x768 V V V V Note 1: Even if the preset timing is entered, a little adjustment of the functions such as Horizontal period, CLK-delay and display position, are required. The adjusted values are memorized in every preset number. Note 2: This module recognizes the synchronous signals with near preset timing of the frequency of the HS and Vsync, even in the case that the signals other than the preset timing that were entered. Note 3: Because adjustments may not fit, such as differing magnifying ratios or, in the case that you use it except for the display timing that was preset. FPM-3150 Series User Manual 18 LU C OSD Operation Keypad Appendix C OSD Operation Keypad C.1 OSD Board Overview The OSD keypad, including six keys and a two color indicator, is designed as the OSD operation interface C.1.1 OSD Button Description Buttons Descriptions Power Turn the monitor power ON or OFF. Auto/Exit Automatically adjust the clock, phase, H-position and V-position. Exit menu. Down/Right/ Increase Activate the volume control. Move the selector to the next option. Increase the gauge value of the selected option. Up/Left/ Decrease Active volume control. Move the selector to the previous option. Decrease the gauge value of the selected option. Menu/Sel Activate the OSD menu. Enter/confirm the selected option. Source Changes Input video source C.1.2 LED Function ON Green StandBy/OFF Green Blinking No Signals Orange FPM-3150 Series User Manual 20 C.2 OSD Key Functions Each selected value is stored into LCD memory after SEL signal input or time out. The stored values are not affected if the power is turned off. But the selected value is not available in case a selected mode is changed before time out or power is turned off before time out. TIME OUT ^ 5-6 seconds ( Can be set in OSD Manager) The default definition of input keys is shown as following: C.2.1 Menu Start Generate Main Menu Press MENU Button in OSD function key • Main Menu -- DISPLAY IN SCREEN Sub-Menu - DISPLAY IN SCREEN N/A Available Key Functions N/A I I N/A Select to exit menu or wait for time out N/A N/A N/A 21 Appendix C C.2.2 Input Source Select • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmation Main Menu -- DISPLAY IN SCREEN Sub-Menu - DISPLAY IN SCREEN ANALOG INPUT DIGITAL INPUT ♦ S VIDEO INPUT CVBS INPUT A at« Sflfd Inpul ON Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm B Decrease the gauge value of the selected option. N/A FPM-3150 Series User Manual 22 4. Auto Select Input • ON ^ start from default setting and scan the inputs by following sequence from ANALOG INPUT, DIGITAL INPUT, S-VIDEO INPUT, and CVBS INPUT. • OFF ^ start from default setting C.2.3 Contrast/ Brightness Setting • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmation • Main Menu -- DISPLAY IN SCREEN 23 Appendix C • Available Key Functions Power Off the LCD Monitor Increase the gauge value of the selected option. Return to last menu Selected to confirm Decrease the gauge value of the selected option. N/A RECALL VALUE - User Define • Reel ^ Pressed to record 1st setting as recall value followed by current screen setting • Rec2 ^ Pressed to record 2nd setting as recall value followed by current screen setting • Recall ^ Switch the setting change by Recl and Rec2 while pressed C.2.4 Geometry Menu - For DVI Input • Generate Main Menu Select by Left and Right Button, press Menu Button for selection confirmation • Main Menu -- DISPLAY IN SCREEN Sub-Menu - DISPLAY IN SCREEN FPM-3150 Series User Manual 24 Available Key Functions Power O...