This means that after switching off the display or after switching to a different memory scan mode, the value for contrast and brightness is restored to the calibrated position. - The calibrated position for contrast and brightness is determined by calibration of the video levels (see § 3.4 below). In case you feel unsatisfied with the current calibrated position, you need to repeat the calibration. The proper way to do this, is to use the automatic calibration routine. However, you can also man

How to use the controls 1. When the OSD is not on the screen, touch any of the soft touch keys. The front illumination is switched on for about 10 seconds. 2. While the illumination is on, touch the Enter touch key to display the main menu. It contains several submenus. 3. To open a submenu, use the Up or Down touch keys to select the submenu. Next, press the Enter touch key to open the submenu. 4. To exit from a submenu, use Up or Down to select EXIT. Next, press Enter . If you exit from the Ma

Sharp edged or hard articles are prohibited. The gathering of dew in the panel may occur with abrupt temperature or humidity changes. A stable environment condition is recommended. Keep the surface clean. No adhesives should be applied. Avoid high voltage and static charge. Wall mounting You can mount the panel to the wall instead of to the foot, by means of the supplied mounting plate. If you do not need to mount the panel to the wall, please skip this item. Step 1: Remove the panel from the fo

• Reconfigure the resolution of your computer to make it less than or equal to the native resolution (1920 x 1200). Problem: Image has vertical flickering line bars. • Use “Clock” to make an adjustment. • Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD Display. Problem: Image is unstable and flickering • Use “Phase” to make an adjustment. Problem: Image is scrolling • Check and make sure the video signal cable (or adapt

2 Switch on the display by pushing the Power key (9). 3 If necessary, select a suitable resolution in the computer operating system. Please refer to Appendix A, "Possible resolutions" in the back of this manual. Note: The recommended resolution for best image quality is 1280x1024 at 60 Hz. The microcontroller in the display checks if the connected video signal has been adjusted before, and if these adjustments have been stored in the memory. There are 2 possibilities: a) The video signal has bee

. Power LED Green : Normal mode Amber: Standby mode Amber: Soft power-off . On-Screen Display (OSD) Function Button 1. POWER : Turns ON/OFF the monitor. 2. MENU : With OSD deactivated, Activate the OSD menu. With OSD activated, Exit from main menu or sub menu. 3. PIP : With OSD deactivated, Hot key of PIP mode. 4. UP : With OSD deactivated, Hot key of the brightness control and increases the brightness. With OSD activated, move the cursor upward. 5. DOWN : With OSD deactivated, Hot key of the br

Release the display panel from the display stand as follows: • Remove the neck cover (1) by sliding it upward. • Lift the plastic frame (2) that covers the fixation of the panel to the stand. Turn it for 45 degrees to uncover the fixation screws. • Unscrew the four fixation screws fixing the panel to the stand. 1 2 Vesa-mount installation 2. Attach the panel firmly to the arm stand using 4 screws M4 x 10 mm. 3. You should mount the panel in landscape position. Portrait position is not supported.

When do you need to use the Autoset functions? It is necessary to perform the Auto Gain and Auto Phase calibrations in the following cases: • The first time you use the display on an analog video • After connecting or selecting another analog video source It is necessary to perform the Automatic Geometry function in case you notice the image geometry or positioning is not as desired. Required test pattern To obtain good results with the autoset functions, it is necessary to have a good image on

Image persistence. • Image persistence is when a residual or “ghost” image of a previous image remains visible on the screen. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. See chapter “Recommended use”. Image is unstable, unfocused or swimming in apparent. • Signal cable should be completely attached to the computer. No signal • Signal cable should be completely attached to the computer. • Make certain the computer is not in a power-saving

We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work wh