Évaluations - 3, GPA: 5
(
)
)
|
Facilité d'utilisation
BEKO plc declines to accept any liability should the instructions not be followed. 4 IMPORTANT INSTALLATION INSTRUCTIONS 1. The space in the room where the appliance is installed must not be smaller than 10 cubic metres. 2. If possible avoid placing the appliance near cookers, radiators or in direct sunlight as this will cause the compressor to run for long periods. If installed next to a source of heat or refrigerator, maintain the following minimum side clearances: From Cookers 2" (50 mm) From Radiators 12" (300 mm) From Refrigerators or Larder Fridge 1" (25 mm) 3. Make sure that sufficient room is provided around the appliance to ensure free air circulation. Thermostat 4. Fit the two plastic wall spacer supplied with the appliance rotating 1/4 turn to the condenser at the back of the refrigerator (see diagram). 5. The appliance should be located on a smooth surface. The two front feet can be adjusted as required. To ensure that, your appliance is standing upright adjust the two front feet by turning clockwise or anti-clockwise, until the product is in firm contact with the floor. Correct adjustment of feet avoids excessive vibration and noise. 6. Refer to "Cleaning and Care" section to prepare your appliance for use. 7. Thermostat is located on the rear wall of the cabinet (See above diagram) and controlled by the thermostat knob located on the indicator light set. (See diagram on page 8) 8. A special receptacle is supplied to store the mains plug during transit. The receptacle is fixed at the back of the cabinet, on the left hand side of the compressor. (See diagram) Gently remove the plug from the receptacle. Never pull the mains cord, you may damage the appliance. In the case of transportation, ensure you locate the plug in the receptacle provided to avoid transit damage. 5 REPOSITIONING THE DOOR Follow the step by step instructions and the diagram below. Numbers in brackets 6 refer to diagrams. a b b 1 60° 7 6 2 3 4 5 10 9 11 8 12 1. Switch off at the socket outlet and pull out the mains plug. 2. Remove all food, loose items and fittings from inside the appliance and door shelves. 3. Carefully tilt the appliance on its back side. (1) (You may need somebody to help you.) Take care not to damage the appliance by laying on some protective material (e.g. its original packaging). Make sure that you tilt the appliance on its back side, otherwise compressor oil may block the pipes and you may damage the appliance. 4. Unscrew and remove the LHS front feet (2). 5. Unscrew the bolts and remove the bottom hinge while holding the door (3). 6. Remove the door carefully from the top hinge by sliding towards the right hand side (4). 7. Reposition top hinge bushing and blanking plug on the opposite side and stand the door safely (5). You may find it easier to remove the bushing and the plug with the tip of a small screwdriver. Take care not to mark the door. 8. Reposition the top hinge on the opposite side (6 and 13). 9. Remove the top trim bottom cover as shown in the figure. (7) Cut the shaded part from left hand side of top trim bottom cover. 10. Fit the top trim bottom cover as shown in the figure. (8) 11. To refit the door, locate the top hinge in the door, attach to the cabinet and hold the door (10). 12. Fit the bottom hinge (11). If necessary adjust and then tighten the bolts. Ensure, that the door opens and closes easily and that there are no gaps allowing air into the cabinet. If there are gaps between the door seal and the cabinet, adjust the door seal by gently pulling away from the door using fingers. 13. Fit the other front feet (12). 14. Carefully stand your appliance. (You may need somebody to help you.) Adjust the front feet (See Installation Instructions) 15. Put back all, loose items and fittings. 16. Wait for at least 4 hours to allow the system to settle before switching on. Spare plastic parts supplied with the appliance are for your future use during door repositioning. 7 INDICATOR LIGHTS There are three coloured indicator lights located on the front of the appliancewhich shows the operating mode of the freezer. Green Indicator (1) Illuminates when the appliance is connected to the mains and will glow as long aselectricity is available. The green light will not glow if the thermostat is set in the '0' position. The green indicator does not give any indication of the temperatureinside the freezer. Amber Indicator (2) This indicator will glow when the fast freeze switch (4) is on and will continue toglow until the fast freeze switch is turned off. The compressor will run continuously while fast freeze switch is on. Fast freeze operation is for freezing fresh food (seeFreezing Fresh Food, page 11). Red Indicator (3) Illuminates: a. If the pre-set temperature can not be maintained. b. If excessive amounts of fresh food are placed inside. c. If the appliance door is left open accidentally. Thermostat knob (5) Thermostat knob is located on the indicator light set. IMPORTANT : When you press the fast...