Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
@ Front speakers @ Center speaker Position inthecenter of thetwo front speakers. In addition, position on or below the TV set, if connecting a TV set to the unit. @ Surround speakers Place the surround speakers directly to the side of or slightly behind the listening area. Align them horizontally, about 1 meter (3,2 feet) above ear height. @ Sub woofer Place the sub woofer in any place between the two front speakers. m Sound from the surround speakers or center speaker depends on the setting of the DSP, Dolby Pro Logic and 5.1 CH function. CONNECTING THE SUPPLIED ANTENNAS @ Connect the FM antenna to the FM 75 Q terminals and the AM antenna to the AM LOOP terminals. FM antenna r( )%7 To stand the AM loop antenna on a surface Fix the claw to the slot as shown in the illustration. To position the antennas FM feeder antenna: Extend this antenna horizontally in a T shape and fix its ends to the wall. AM loop antenna: Position for the best reception. l Do not bring the FM antenna near metal objects or curtain rails. . Do not bring the AM antenna near other external equipment, the unit itself, the AC power cord or speaker cords, as noise will be picked up. Do not unwind the AM loop antenna wire. CONNECTING AN OUTDOOR ANTENNA For better FM reception, use of an outdoor antenna is recommended. Connect the outdoor antenna to the FM 75 Q terminals. w 5 ENGLISH FUNCTION button A130UTTHEREMOTE CONTROL Insertingbatteries Detach the battery cover on the rear of the remote control and insert two R6 (size AA) batteries. R6(AA) When tc) replace the batteries The maximum operational distance between the remote control and the :sensor on the unit should be approximately 5 meters (16 feet) When this distance decreases, replace the batteries with new ones. Using the remote control The instructions in this manual refer mainly to the buttons on the main unit. Buttons on the remote control with the same names as those on the main unit can be used as well. e If the unit is not going to be used for an extended period of time, remove the batteries to prevent possible electrolyte leakage, * The rernote control may not operate correctly when: -The line of sight between the remote control and the remote senscr in the display window is exposed to intense light, such as dir,ect sunlight. - Other remote controls are used nearby (those of television, etc.) Remote control operation This remote control system allows you to operate other external equipment besides the AIWA receiver. For details of the remote control operation for other external equipment, see “REMOTE CONTROU on page 16. Hereupon, it is explained how to operate the Aiwa receiver. Each time this button is pressed, the sound source changes FM (or AM)aJ +V3+V2-~Vl~CD+AUX+~ PHONO cyclically. a): Either band, which you have tuned in for the last time, (comes on. TUNER PRESET/SURROUND buttons Tune in the station which has been preset on the receiver. To go to a higher preset number, press the UP>Pi button. To go to a lower preset number, press the DOWN-button. This button is also used when adjusting the speakers level balance of the DSP, Dolby Pro Logic or 5.1 CH mocle. m It is not necessary to press the AIWA RECEIVER button each time you operate the Aiwa receiver unless another mode has already been set. (See “REMOTE CONTROU on page 16.) If the receiver cannot be operated with thle remote control Follow the steps below with the remote control. 1 Press the AIWA RECEIVER button. 2 Press and hold the SET UP button for about 2.5 seconds. The indicator on the top of the remote control blinks twice while pressing the button. 3 Press the DIGIT buttons in the order c)f “4;’ “O” and “6.” RECEIVER KEY Al\/V/+ RECEIVER MUTE TUNER PRESET/ POWER SURROUND ‘uNcT’ONevOLuME 1 Press the AIWA RECEIVER button to set the remote control to the Aiwa receiver mode. 2 Press one of the buttons indicated above. 15NGL/!3H 6 BEFORE OPERATION SETTING THE CLOCK POWER TAPE MONITOR VOLUME Function indicators PHONES FRON+SPEAKERSA, B Function buttons To turn the unit on Press one of the function buttons (TUNER, PHONO, AUX, CD, VIDEO 1/5.1 CH, VIDEO 2 or VIDEO 3) or the TAPE MONITOR button. When pressing the TUNER button, the previously tuned station is received (Direct Play Function). The POWER button is also available. Operation is possible after four seconds, while the VOL (volume) level or function name is displayed one after the other and the selected function indicator flashes. To select the front speaker system To use speaker system A: Set the FRONT SPEAKERS A button to sON. To use speaker system B: Set the FRONT SPEAKERS B button to ~ON. To use both speaker systems: Set both the buttons to ~ ON. Set the button(s) to IOFF to turn off the speaker system(s). As the front speaker systems A and B are connected in series: -The sound will be slightly decreased when using both speaker systems -No sound can be heard if the FRONT SPEAKERS A and B buttons are set to -ON when only one speaker system is connected Using the ...