Évaluations - 3, GPA: 4.3
(
)
)
|
Facilité d'utilisation
repeatedly until “PLAY SEL” appears, then press ENTER .. To cancel the timer Repeat the same procedure as above until “OFF” appears, and then press ENTER .. To change the setting Start over from step 1. Tip The Play Timer setting remains as long as the setting is not cancelled manually. Other Operations GB Others Troubleshooting 1 Make sure the power cord and speaker cords are correctly and firmly connected. 2 Find your problem in the checklist below, and take the indicated corrective action. If the issue persists, contact your nearest Sony dealer. If “PROTECT” appears on the display Immediately unplug the power cord, and check the following items. . If your system has a voltage selector, is the voltage selector set to the correct voltage? . Are the + and . speaker cords short-circuited? . Are you using only the supplied speakers? . Is anything blocking the ventilation holes on the top or back of the system? After you have checked these above items and found to be all right, reconnect the power cord, and turn on the system. If the issue persists, contact your nearest Sony dealer. General The system does not turn on. .Is the power cord plugged in? .Is the voltage selector set correctly to match the local power line voltage? Sound comes from one channel, or the left and right volumes are unbalanced. .Place the speakers as symmetrically as possible. .Connect only the supplied speakers. Sound lacks bass. .Check that the Black (or Red) cord is connected to the speaker’s . (or +) jack correctly. Severe hum or noise. .Move the system away from sources of noise. .Connect the system to a different wall socket. .Install a noise filter (available separately) to the power cord. The remote does not function. .Remove any obstacles between the remote and the remote sensor . on the unit, and position the unit away from fluorescent lights. .Point the remote at the system’s sensor. .Move the remote closer to the system. GB CD/MP3 player The sound skips, or the disc will not play. .Wipe the disc clean, and replace it. .Move the system to a location away from vibration (for example, on top of a stable stand). .Move the speakers away from the system, or place them on separate stands. At high volume, speaker vibration may cause the sound to skip. Play does not start from the first track. .Press PLAY MODE . repeatedly until both “PGM” and “SHUF” disappear to return to normal play. Starting playback takes more time than usual. .The following discs take a longer time to start playback. .a disc recorded with a complicated tree structure. .a disc recorded in multisession mode. .a disc that has not been finalized (a disc to which data can be added). .a disc that has many folders. USB device You cannot start recording to an USB device. .The following problems may have occurred. .The USB device is full. .The number of MP3 files and folders on the USB device has reached the upper limit. .The USB device is write-protected. Recording is stopped before it is finished. .You are using an unsupported USB device. See “Playable/Recordable USB devices” (page 35) for the supported device types. .The USB device is not formatted correctly. Refer to the USB device operation manual for how to format. .Turn off the system and remove the USB device. If the USB device has a power switch, turn the USB device off and then on again after removing it from the system. Then perform recording again. .If the recording and erase operations are repeated multiple times, the file structure within the USB device becomes fragmented. Refer to the USB device operation manual for how to deal with this problem. Recording to an USB device results in an error. .You are using an unsupported USB device. See “Playable/Recordable USB devices” (page 35) for the supported device types. .The USB device was disconnected or the power was turned off during recording. Delete the partially- recorded file, and record again. If this does not fix the problem, the USB device may be broken. Refer to the USB device operation manual for how to deal with this problem. .Turn off the system and remove the USB device. If the USB device has a power switch, turn the USB device off and then on again after removing it from the system. Then perform recording again. Others Continued . GB Files are not played back in the recorded order. .When recording after the erase operation has been performed, the new folders and files are registered to the erased locations, so files may not be played back in the recorded order. Files or folders on the USB device cannot be erased. .Check if the USB device is write- protected. .The USB device was disconnected or the power was turned off during the erase operation. Delete the partially-erased file. If this does not fix the problem, the USB device may be broken. Refer to the USB device operation manual for how to deal with this problem. Are you using a supported USB device? .If you connect an unsupported USB device, the following problems may occur. See “Playable/Recor...