Évaluations - 3, GPA: 3.7
(
)
)
|
Facilité d'utilisation
When shipped from the factory, the CUBE-40XL’s FOOT SW TYPE is set to the momentary type. For details on how to change this setting, refer to”Using a Latch-type Foot Switch” (p. 10). * The CUBE’s FOOT SW (foot switch) jacks are TIP TRS type jacks, and support plugs of the type shown in the illustration. Use TRS cables to connect your foot switch. RING EXT SPEAKER (CUBE-80XL only) 5. EXT SPEAKER Jack This is for connecting an external speaker. When an external speaker is connected, sound is played both from the external speaker and from the unit’s built-in speaker. * When connecting to an external speaker, make sure the speaker conforms to the following specifications. Impedance: 8 ohms or less Allowable power input: 80 watts or greater * Only use speaker cable to connect the speaker. Do not use any shielded cable designed for use with guitars. RECORDING OUT/PHONES 6. RECORDING OUT/PHONES Jack This functions either as an output jack for recording or as a phones jack. This features COSM speaker modeling, enabling production of impressive guitar sound. Adjust the volume using the [VOLUME] knobs for the JC CLEAN and LEAD channels and the SOLO function. * When a plug is connected to this jack, no sound is played from either the unit or any connected external speaker. This is handy at night or in other situations when you want to avoid high-volume sound from the speakers. When using as an output jack for recording Use a monaural 1/4” phone plug to connect a recorder or other recording device. When using as a headphones jack Connect headphones. LINE OUT (CUBE-80XL only) 7. LINE OUT Jack This is for connecting a PA system, recorder, or other external equipment. This features COSM speaker modeling, enabling production of impressive guitar-amp sound. You can use this in conjunction with an external PA system, or to record your performance via direct line while monitoring the sound from the CUBE’s speaker. Adjust the output level using the [VOLUME] knobs for the JC CLEAN and LEAD channels and the SOLO function. * The sound from AUX IN is not output from LINE OUT. AUX IN 8. AUX IN Jack This lets you connect a CD player, digital audio player, electronic instrument, or other such device and play it at the same time as the guitar. This accepts a stereo miniature phone plug. However, the speaker and RECORDING OUT/PHONES output is monaural. Use a cable (sold separately) that’s appropriate for the device you’re connecting. * Determine the volume level by adjusting the volume control of the connected device. * When connection cables with resistors are used, the volume level of equipment connected to the AUX IN jack may be low. If this happens, use connection cables that do not contain resistors. Nederlands Portugues Espanol Italiano Francais DeutschEnglish Using a Latch-type Foot Switch Using a Latch-type Foot Switch FOOT SW TYPE setting There are two types of foot switches. Type Operation Momentary type (BOSS FS-5U, etc) This type remains on (or off ) while depressed and switches off (or on) when released. Latch type (BOSS FS-5L, etc.) This type switches on or off each time it is depressed. * The BOSS FS-6 can operate as either a momentary or latch-type pedal switch. CUBE-40XL At the factory settings, the momentary type is selected. You can change this setting as follows. • To specify the latch type Turn on the power while holding down the [TAP/STOP] switch. • To specify the momentary type Turn on the power while holding down the [REC/PLAY/DUB] switch. CUBE-80XL Set the [FOOT SW TYPE] switch on the rear panel to FS-5L (LATCH). * The setting you specify is remembered even while the power is turned off. Foot Switch Settings BOSS FS-5L (RING) (TIP) Polarity switch REVERB EFX SOLO CH SELECT BOSS FS-6 BASet the switches as shown as bellow. REVERB EFX SOLO CH SELECT BOSS FS-5L+FS-5U (RING) (TIP) TAP/STOP DELAY/ REC/PLAY/DUB Polarity switch DELAY/ TAP/STOP BASet the switches as shown as bellow. BOSS FS-6 REC/PLAY/DUB * Even if FOOT SW TYPE is set to FS-5L (LATCH), you must always use a momentary-type foot switch for TAP/STOP. This function will not work correctly with a latch-type foot switch. Important Notes When Using a Latch-type Footswitch Pedal The on/off state of the footswitch pedal takes precedence over the control panel for switching EFX, delay, or reverb on and off. However, the on or off states of EFX, delay, or reverb stored in memory using the SOLO function take precedence when saved SOLO-function panel settings are called up. Such cases may result in conflicting indicator displays on the control panel and the footswitch pedal, but this is not a malfunction. Convenient Applications You can use either of the following settings to control operation when the panel settings for EFX, delay, and reverb are called up using the SOLO function. Foot switch priority mode Make the on/off state of the footswitch pedal always take priority. To make the setting: Hold down the [SELECT] switch and switch on the power. Memory priority m...
Ce manuel est également adapté pour les modèles :Instruments de musique - CUBE 80XL (16.27 mb)
Instruments de musique - CUBE-40XL (16.27 mb)