Évaluations - , GPA:
(
)
)
Fabricant : Numark Industries
Taille : 3.54 mb
Nom Fichier : da605976-c34f-4fbe-a1a6-bae495080ebe.pdf
Langue d'enseignement: 
Le document est chargé, s'il vous plaît patienter
 |
Le document est chargé, s'il vous plaît patienter
Facilité d'utilisation
4. LINE INPUTS (RCA) – Connect line-level devices, such as CD players, samplers or audio interfaces, to these inputs. 5. PHONO INPUTS (RCA) – Connect phono-level devices, such as turntables, to these inputs. 6. GROUNDING TERMINAL – If you are using phono-level turntables with a grounding wire, connect the grounding wire to these terminals. If you experience a low “hum” or “buzz”, this could mean that your turntables are not grounded. Note: Some turntables have a grounding wire built into the RCA connection and, therefore, nothing needs to be connected to the grounding terminal. 7. LINE | PHONO SWITCH – Flip this switch to select between the PHONO INPUT or LINE INPUT for each channel. 8. USB – These USB connections send and receive audio from a connected computer. The USB 1 jack can receive audio and send it to the mixer’s Channel 1. The USB 2 jack can receive audio and send it to the mixer’s Channel 2. They can also function as outputs, sending audio to your computer. For more information, refer to the USB OPERATION section. TOP PANEL FEATURES 1. POWER LED – Illuminates when the mixer is on. 2. MASTER – This control adjusts the output volume of the Program mix. 3. MIC GAIN – Adjusts the audio level of the microphone signal. 4. CUE GAIN – Adjusts the level of the headphone audio. 5. CUE SLIDER – Slide this to mix between Channels 1 and 2 in the headphones. When all the way to the left, only Channel 1 will be heard. When all the way right, only Channel 2 will be heard. 6. CHANNEL GAIN – Adjusts the corresponding channel’s pre-fader and pre-EQ gain level. 7. CHANNEL TREBLE – Adjusts the high (treble) frequencies of the audio on the corresponding channel. 8. CHANNEL BASS – Adjusts the low (bass) frequencies of the audio on the corresponding channel. 9. INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks are located on the rear panel. 10. CHANNEL FADER – Adjusts the audio level on the corresponding channel. 11. CROSSFADER – Blends audio playing between Channels 1 and 2. Sliding this to the left plays channel 1 and sliding to the right plays Channel 2. Note: The crossfader is user-replaceable if it should ever wear out. Simply remove the facepanel, then remove the screws holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer only. 12. MIC INPUT – Connect .” microphones to this input. The microphone controls are located on the top panel. 13. HEADPHONES – Connect your .” headphones to this output for cueing and mix monitoring. 6 6 7 7 3 4 5 4 5 2 1 8 USB OPERATION The M1USB is equipped with two USB ports which allow you to play content from your computer through the mixer, or record audio from the mixer directly into your favorite software application. The USB interface on your mixer works with your computer just like a standard USB sound card. In addition, the USB interface is class-compliant, so there are no special drivers or software to install; simply connect a USB cable from either or both USB ports to your computer and you are ready to go! WINDOWS CONFIGURATION 1. Turn on your computer and the M1USB. 2. Use a USB cable to connect one (or both) ports of the M1USB to your computer. 3. Windows will immediately recognize the mixer as a “USB Audio Device” or “USB Audio CODEC” and will automatically install any required system components. To change system audio preferences in Windows, you will need to access the Sounds and Audio Devices properties, located in the Control Panel. To access audio device settings, click on the Audio tab. The first time you connect the M1USB to your computer, the mixer will be automatically assigned as the Default (or “Preferred”) Device for sound playback on your computer. All of your computer’s sounds will be sent to the mixer channel indicated above the USB connection. Note: If you have connected both USB ports to your computer, the ports will be numbered in the order they were connected. For example, if you connected USB A before USB B, USB A will appear as “USB Audio CODEC” and USB B will appear as “USB Audio CODEC (2)”. • To send audio from your computer into the M1USB, select “USB Audio CODEC” in the Sound Playback field. This allows you to play audio from your computer into one of either of the mixer channels, depending on which USB port is used to make the connection. • To send audio from the M1USB to your computer, select “USB Audio CODEC” in the Sound Recording field. This allows you to record your mix into your computer. Note: If your sound playback or recording application does not have its own audio input and output settings (for example, Windows Sound Recorder, Windows Media Player or Apple iTunes), it will use the devices set in Sounds and Audio Devices. Please note that these settings are loaded upon application startup, so if you change device settings while the application is open, you will need to restart your application for the settings to take effect. Tip: To pre...