Évaluations - 4, GPA: 4
(
)
)
|
Facilité d'utilisation
One of the ACTIVE CHANNEL LEDs (6) will illuminate to indicate that the unit is on. Pressing the lower portion of the switch turns the unit off. BACK PANEL Due to differences in the layout and features of the back panel, both the 112 and 212 back panels are presented. Refer to the illustration that identifies your model. 112 EFX 19 18 2021 22 212 EFX 19 23 20 24 25 26 2722 (19) IEC CONNECTOR This is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings for the intended operating voltage is included. The mains cord should be connected to the amplifier before connecting to a suitable AC outlet. U.S DOMESTIC AC MAINS CORD The mains cord supplied with the unit is a heavy-duty, 3-conductor type with a conventional 120 VAC plug with ground pin. If the outlet used does not have a ground pin, a suitable grounding adapter should be used, and the third wire should be grounded properly. Never break off the ground pin on any equipment. It is provided for your safety. NOTE: FOR UK ONLY If the colors of the wires in the mains lead of this unit do not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E, the earth symbol, colored green, or colored green and yellow. (2) The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. (3) The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red. 6 (20) REMOTE SWITCH CONNECTOR This 8-pin DIN connector is provided for the connection of the PFC 3 footswitch (included). The footswitch cable should be connected before the amp is powered up. See the FOOTSWITCH section of this manual for explanation of switch operation. (21) HEADPHONE JACK . (25) POWER AMP IN This 1/4" jack allows the connection of line level signals directly to the power amp. (26) PREAMP OUT This 1/4" jack allows patching to mixing consoles, tape recorders, etc. Use a shielded cable to patch from this jack to the input of the device receiving the signal. This patch does not affect the operation of the amplifier or the signal continuing to the power amp and speakers. (27) EFFECTS LEVEL This switch selects the EFFECTS LOOP (22) sensitivity to avoid overdriving effects with no input level control. 7 FOOTSWITCH 3 PRESET MODULATIONCHANNEL DELAY REVERB EFX SELECT MODE TM 28 30 31 32 33 34 3529 MODE SELECT The PFC 3 footswitch operates in two modes: EFX Select mode and Preset Select mode. Pressing the MODE SWITCH (28) selects between the two modes. The active mode is indicated by the MODE LED (29). Illumination of the LED indicates EFX Select Mode; a dark LED indicates Preset Select Mode. Controls and indicators 30-35 perform different functions relative to the active mode. PRESET SELECT MODE In this mode, all three switches control effects presets. Their corresponding LEDs indicate which preset is active. Once desired settings are achieved utilizing the effects controls on the front panel, double-click one of the Preset switches (30, 33, or 35) to store the settings. To return to the last saved settings for a Preset, press the desired Preset switch once. For a detailed explanation on creating and storing presets, refer to the TWEAK FEATURES section of this manual on the following page. EFX SELECT MODE NOTE: When entering this mode, the current preset will remain active. In this mode, SWITCH 1 (30) selects between the Lead and Clean channels. The CHANNEL LED (31) will illuminate when the Lead channel is active. SWITCH 2 (33) toggles between two effects and their respective settings. This switch may be used as an on/off switch if one of the settings has no effects active. To use the MODULATION LED (32) as a status indicator, the “off” (or lower setting) should be made with the LED dark, and the “on” (or higher setting) made with the LED illuminated. SWITCH 3 (35) toggles between two reverb and delay settings. As with effects settings, this switch may be used as an on/off for reverb and delay. Both functions change simultaneously when this switch is depressed. 8 TWEAK FEATURES EFX amplifiers offer hidden features to further adjust the parameters of the digital effects. In addition to the adjustments described in the EFXADJ PARAMETERS section of this manual, additional tweaks may be made to customize effects to user preference. Tweaks are made by pressing and holding the EFX ADJUST (12) control while simultaneously rotating the REVERB (13) control. The EFXADJUST control must be pressed for at least one second to enter Tweak Mode. Reverb setting will not be affected while in Tweak Mode. The LED ring surrounding the control will now reflect the value of the effect being tweaked. As in standard parameter changes, the effect being tweaked will be the active effect as indicated by the LED adjacent to the effect name. TWEAK ADJ PAR...
Ce manuel est également adapté pour les modèles :Instruments de musique - Transtube 9/0180305014 (2.37 mb)
Instruments de musique - Transtube 9/0180305014 (2.37 mb)
Instruments de musique - Transtube 112/212 EFX (2.37 mb)