Évaluations - 3, GPA: 4.7
(
)
)
|
Facilité d'utilisation
Next push the Global button until the following screen is displayed: ENUFLT Fre-=i CCNTRL] #1 Pram C# Ch Sc Move the cursor under Pram and use the ▼ and A buttons to select Freq. Next move the cursor under C# and select Cntrl#=7. Next move the cursor under Ch and select RCV. Next move the cursor under Sc and select +100 It is important to note that the scale can be set from ±100 allowing normal or reverse wah wah effects. You can set the scale anywhere in between to adjust the effect to your tastes. Next press die Edit button and move the cursor under Sn and select a sensitivity level. Try +48 to start. Next move the cursor under Fq and select a frequency (try 50). Next move the cursor under Rs and set the resonance (try 52). Next move the cursor under Ty to select a filter (try LP-Slo). Next move the cursor under Mx and try a mix level of 50%. Now work the continuous controller pedal to try the effect. Adjust the envelope filter parameters and the scale to suit your taste. Press the Store button to save the settings and continuous controller to your preset. Note: If you get volume control instead of wah wah. push the Global button until the following screen is displayed: U0LIJME = 100 CU0L] m i d i : 0 N #7 Sc=+54 Move the cursor under midi and change the setting to OFF. Now try your effect. You can also use the 4-band parametric FQ to create this effect. Appendix A Individual Effects TransTube (TB) The TransTube effect uses the patented Transmbe technology to alter the audio signal in a more traditional manner. The TransTube effect has four modes (or voices) to select from. These are accessed by using the Mode button. Note: To change the TransTube mode, you must be in Play Mode (accessed by pressing the Play button ). Edit Mode (accessed by pressing the Edit button), or the TransTube page (accessed when you press the Edit button a second time to begin editing the TransTube parameters). Configuration when TB is on front end of / effects chain Signal Input / H> rransTuhe Preamp rransTulK' Stages [> Solid-State Preamp ■o- Global Input Level k All other settings \ ADC DSP Note: The Global Input Level is non-functional when the Transtube (TB) is at the front of the effects chain. Sj CLEAN Two gain stages and a passive HQ to achieve dean to slightly distorted tones. £> CRUNCH Three gain stages and a passive EQ for medium distortion amounts. a LEAD Four gain stages and a passive EQ for high gain distortion. a ULTRA Same as Lead, except with active F.Q. allowing for greater tonal variation. Parameters Pr: The Pr (Pregain) parameter adjusts the amount of gain the signal has before entering the preamp. Range is 0-100. When TB is present in a chain, turning the Pre Gain knob will alter this parameter’s value even if you are not directly editing the TB parameters. Pci The Pd (Pad) parameter changes gain of the first TransTube stage without effecting tone. Select either Hi (for distortion) or Lo (for clean). Pt: The Pt (Postgain) parameter adjusts the amount of gain the signal has as it leaves the preamp. Range is 0-100. When TB is present in a chain, turning the Post Gain knob will alter this parameter’s value even if you are not directly editing the TB parameters. Note: The previous three parameters apply to all four TransTube modes; however, the following four parameters (Bs, Mi, Tr, Ps) change to Bt. Bd. Sd, Sh, respectively, when ULTRA is selected as the mode. Clean, Crunch, Lead parameters (Passive EQ) JBs: The Bs (Bass) parameter adjusts the amount of low frequencies present in the audio signal. Range is 0-100. When TB is present in a chain, turning the Bass knob will alter this parameter’s value even if you are not directly editing the TB parameters. Mi: The Mi (Middle) parameter adjusts the amount of midrange frequencies present in the audio signal. Range is 0-100. When TB is present in a chain, turning the Mid knob will alter this parameter’s value even if you are not directly editing the TB parameters. Tr: The Tr (Treble) parameter adjusts the amount of high frequencies present in the audio signal. Range is 0-100. When TB is present in a chain, turning the Treble knob will alter this parameter’s value even if you are not directly editing the TB parameters. Ps: The Ps (Presence) parameter determines the amount of high frequency boost or cut. Range is ±30. Ultra parameters (Active EQ) Bt: The Bt (Bottom) parameter adjusts the amount of low frequencies present in the audio signal. Range is ±50. When TB is present in a chain, turning the Bass knob will alter this parameter’s value even if you are not directly editing the TB parameters. Bd: The Bd (Body) parameter adjusts the amount of midrange frequencies present in the audio signal. Range is ±50. When TB is present in a chain, turning the Mid knob will alter this parameter’s value even if you are not directly editing the TB parameters. Ed: The Ed (Edge) parameter adjusts the amount of high frequencies present in th...
Ce manuel est également adapté pour les modèles :Instruments de musique - TransFex Pro 212s (5.63 mb)