|
Facilité d'utilisation
For full range, wire the Speakon® connectors as follows: Pin 1+ : Full Range positive (+) Pin 1– : Full Range negative (–) BI-AMP OPERATION: • Set the Mode switch to the “Biamp" position. • Set the crossover point for the amplifiers somewhere in the 100Hz to 300Hz range. Once up and running, adjustments within this range may be made to suit your personal listening palate. • 1/4” JACKS: Connect the output of your low frequency amplifier to either of the two 1/4” jacks labeled “Full Range Inputs (Bi-amp Low Inputs).” • Connect the output of your mid/high frequency amplifier to the 1/4” jack labeled “Bi-amp High Input.” (the 1/4” jacks do not allow daisy chaining in the biamp mode.) • SPEAKON® JACKS: Connect the Biamp output of your amplifier to either of the two Speakon® jacks. Use the remaining Speakon® jack to daisy chain to another cabinet, if desired. For biamping, wire the Speakon® connectors as follows: Pin 1+ : Biamp Low positive (+) Pin 2+ : Biamp High positive (+) Pin 1– : Biamp Low negative (–) Pin 2– : Biamp High negative (–) Caution: Power handling for certain components can be lower in Biamp mode, check the label for maximum ratings and use appropriate amplifier settings! INPUT JACKPLATE (located on rear of cabinet): PR-1832HE / PR-1528HE Bass Enclosure TECHNICAL SPECIFICATIONS: PR-1832HE PR-1528HE Impedance 4 ohms 4 ohms RMS Power Handling 600 watts 400 watts Program Power Handling 1200 watts 800 watts Frequency Response (-3dB) 42Hz–18kHz 48Hz–18kHz Frequency Range (-6dB) 38Hz–20kHz 42Hz–20kHz Low Frequency Limit (-10dB) 30Hz 36Hz Nominal Sensitivity (1W/1M) 100dB 96dB Maximum SPL 127dB 122dB Crossover Frequencies (Internal) 200Hz,1kHz, 5kHz 200Hz, 4kHz Dimensions (H x W x D) 39" x 24" x 24" 27" x 24" x 24" Weight 167 lbs 105 Ibs DRIVER COMPLEMENT AND RATINGS IN BI-AMP MODE: Mid/High Frequency Section: Average Power Handling: 300 watts 200 watts Impedance 4 ohms 4 ohms Useful Response 100Hz–20kHz 200Hz–20kHz Midrange Cone Loudspeakers: Size: 2 x 10" Cast 2 x 8" Voice Coil: 2.5" Dia 2" Dia Magnet Wt. 59 oz. 30 oz. Size: 2 x 6-1/2" –N/A– Voice Coil: 1" Dia –N/A– Magnet Wt.: 30 oz. –N/A– High Frequency Driver: Bullet Horn Bullet Horn Throat Size: 3/4" 3/4" Voice Coil: 1.25" Dia 1.25" Dia Magnet Wt.: 14 oz. 14 oz. Low Frequency Section: Average Power Handling: 400 watts 300 watts Impedance: 4 ohms 4 ohms Useful Response: 35Hz–300Hz 45Hz–500Hz Size: 18" 15" Voice Coil: 4" Edge Wound 4" Edge Wound Magnet Wt. 109 oz. (6.8 lbs) 109 oz. (6.8 Ibs) Ampeg continually develops new products, as well as improves existing ones. For this reason, the specifications and information in this publication are subject to change without notice. Ampeg is proudly Made in America. ©1997 SLM Electronics, 1400 Ferguson Avenue, St. Louis, MO 63133 U.S.A. P/N 47-426-01 • 12/97 PR-1832HE / PR-1528HE Bass Enclosure TECHNICAL SPECIFICATIONS: PR-1832HE PR-1528HE Impedance 4 ohms 4 ohms RMS Power Handling 600 watts 400 watts Program Power Handling 1200 watts 800 watts Frequency Response (-3dB) 42Hz–18kHz 48Hz–18kHz Frequency Range (-6dB) 38Hz–20kHz 42Hz–20kHz Low Frequency Limit (-10dB) 30Hz 36Hz Nominal Sensitivity (1W/1M) 100dB 96dB Maximum SPL 127dB 122dB Crossover Frequencies (Internal) 200Hz,1kHz, 5kHz 200Hz, 4kHz Dimensions (H x W x D) 39" x 24" x 24" 27" x 24" x 24" Weight 167 lbs 105 Ibs DRIVER COMPLEMENT AND RATINGS IN BI-AMP MODE: Mid/High Frequency Section: Average Power Handling: 300 watts 200 watts Impedance 4 ohms 4 ohms Useful Response 100Hz–20kHz 200Hz–20kHz Midrange Cone Loudspeakers: Size: 2 x 10" Cast 2 x 8" Voice Coil: 2.5" Dia 2" Dia Magnet Wt. 59 oz. 30 oz. Size: 2 x 6-1/2" –N/A– Voice Coil: 1" Dia –N/A– Magnet Wt.: 30 oz. –N/A– High Frequency Driver: Bullet Horn Bullet Horn Throat Size: 3/4" 3/4" Voice Coil: 1.25" Dia 1.25" Dia Magnet Wt.: 14 oz. 14 oz. Low Frequency Section: Average Power Handling: 400 watts 300 watts Impedance: 4 ohms 4 ohms Useful Response: 35Hz–300Hz 45Hz–500Hz Size: 18" 15" Voice Coil: 4" Edge Wound 4" Edge Wound Magnet Wt. 109 oz. (6.8 lbs) 109 oz. (6.8 Ibs) Ampeg continually develops new products, as well as improves existing ones. For this reason, the specifications and information in this publication are subject to change without notice. Ampeg is proudly Made in America. ©1997 SLM Electronics, 1400 Ferguson Avenue, St. Louis, MO 63133 U.S.A. P/N 47-426-01 • 12/97 ...
Ce manuel est également adapté pour les modèles :Instruments de musique - EXTREME SERIES PR-1528HE (230.43 kb)