Évaluations - 5, GPA: 3.2
(
)
)
|
Facilité d'utilisation
To cancel without jumping, press [ EXlT]. *ln the Orig.Tone (PCM) Play or ROM Play displays, pressing! USER jwili not access the Jump display. * It Is not possible to Jump to a display which has no screen number. 85 ©BASIC PROCEDURES (EDIT MODE) 0 How to set a Jump Destination | Jurcp~setting 23. I select Fi: l.kb prm F2s 2.Part Setting | F35 3.int CTRL Map ! F4! 4.MIDI CTRL Map I__F5i 5.MIDI OUT__ © Display the desired screen. * It is not possible to assign a display which has no screen number. - (5) press 1 USER 1. (The Upper right of the display will show the number and name of the screen you are about to assign.) ® Press ¡ WRITE j. (The Jump Setting display will appear.) © Press the Function button (I FI 1—j F5 1) you wish to assign. To cancel without assigning, press | EXifl. After the assignment has been made, you will return to the display which was assigned. I To return to the previous higher level press EXIT Edit mode is organized in a tree-like structure, and pressing j'" " 1 will return you to the previous higher level. I To return to the Edit menu press EDIT When you press} EDIT I, you will return to the Edit menu display. 86 ©BASIC PROCEDURES (EDIT MODE) 3. How to Modify Settings This section will explain how to modify parameter settings in the selected editing display. ■ Basic procedure to modify settings Use) A 1/1 Tl/| ^ ]yj '► |to move the cursor to the location of the parameter you wish to modify, and use I INC 1/1 DEC lorjg^^l^to modify the value. # How to enter characters When entering a name for a Performance, Patch, Tone, or Tx Channel (MIDI Channel), you can select characters using the following buttons. (The characters are printed In grey below each button.) HH 17b ICT/CAftS COHtAHD ..mu... EHTbT i 1—'=>—I 1 -) 1 —cr=T i { .....n r ID C ...............1 £......-L—. ZD C 1 CAPS SPACE A 0 c » BANK E F C H i j t I 1 2 3 4 5 6 7 e r_ . 1 1 I 1 { ] [ . ID C """ ......“I L.................. ZD C ) il N 1 0 P 2 3 0 R ST 4 5 (1 V - If 6 7 s X 8 0 Y 1 ....."'1 ( J i ) Î ................... I 1 H) C 1 t _ Z3 c I 1 Z 2 / 3 i 4 * 5 1 6. 7 . 8 ! Use 1 A 1/f T |/f < !/!"► 1 to move the cursor to the location where you wish to input the character, and press a button to select a character. The characters will change each time you press the button. CAPS: Switch between upper case and lower case characters. Upper case characters are selected when the Indicator is lit. SPACE: Enter a space. INS: Insert a space and push the following characters back. DEL: Delete a character and pull the following characters forward. You can also select characters using ■ (space) A — 2a — zO — 9 - / + * # ! 87 ©BASIC PROCEDURES CEDIT MODE) ■ Edit using the Tone Palette Sliders While you are in an editing display, up to four parameters of each display can be assigned to sliders, allowing you to edit by moving the sliders. Parameters can be edited even when the cursor is located at a different parameter. It is also possible to to cancel the parameter assignments. * in Edit mode, the Tone Palette Buttons will not function. • To assign a slider * Only parameters can be assigned. It is not possible to assign the following parameters. • Zone, Split Point, Source Key, Mute • Name • Orig,Media, Orlg.Number • Controller Map (D Move the cursor to parameter you wish to assiga As shown below, dots will appear in the display at the left of the parameter or value. The number (1 — 4) of these dots indicates the number of the Tone Palette Slider (1 — 4). This indicates which parameter has been assigned to each Tone Palette Slider. (Example) Dot 1 —■Cutoff —■ * Res o —:Attack ■ —2 Release* • To cancel a slider assignment While pressing the j TONE / ZONE SELECT |of the slider you wish to cancel, press [~EXff1- 88 ©BASIC PROCEDURES (EDIT MODE) ■ Using You can use T TONE/ZONE SELECT ]to do the following. ♦For each Section of the Tone Palette; mute the Tone Thej TONE/ZONE SELECT [buttons 1 —4 correspond respectively to each Section (L-l — U-4) of the Tone Palette. * Do not press two or morel TONE/ZONE SELECT 1 buttons at the same time. • To mute a Tone In an editing display, you can mute the Tone of the Patch (each Section of the Tone Palette) of the Part selected in the display. Press the! TONE/ZONE SELECT }that corresponds to the Tone you wish to mute. When a Tone is muted, the button indicator will go out. [Performance Edit display] Mute the Tone of the Patch of the Part selected in the 2. Part Setting display. * Muting Is not possible if the Rhythm Part is selected. [Patch Edit display] Mute the Tone of the Patch of the Part selected in the 8.Patch Common display. [Tone Edit display] Mute the Tone of the Patch of the Part selected in the l4.Tone PRM display. [System Setup display] Mute the Tone of the Patch of the Part selected In the S.Patch Common display. * You cannot mute a Tone in the Rhythm Setup display. • To select a To...