Évaluations - 2, GPA: 3.5
(
)
)
|
Facilité d'utilisation
.Expression (Controller number 11) Status 2nd byte 3rd byte BnH 0BH vvH n = MIDI channel number: 0H-FH (ch.1-ch.16) vv = Expression: 00H-7FH (0-127), Initial Value = 7FH (127) * These message can affect only MIDI notes. .Hold 1 (Controller number 64) Status 2nd byte 3rd byte BnH 40H vvH n = MIDI channel number: 0H-FH (ch.1-ch.16) vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON * These message can affect only MIDI notes. .Sostenuto (Controller number 66) Status 2nd byte 3rd byte BnH 42H vvH * These message can affect only MIDI notes. n = MIDI channel number: 0H-FH (ch.1-ch.16) vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON * These message can affect only MIDI notes. .Soft (Controller number 67) Status 2nd byte 3rd byte BnH 43H vvH n = MIDI channel number: 0H-FH (ch.1-ch.16) vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON * These message can affect only MIDI notes. .Effect 1 (Reverb Send Level) (Controller number 91) Status 2nd byte 3rd byte BnH 5BH vvH n = MIDI channel number: 0H-FH (ch.1-ch.16) vv = Control value: 00H-7FH (0-127) 0-63 = OFF, 64-127 = ON .RPN MSB/LSB (Controller number 100, 101) Status 2nd byte 3rd byte BnH 65H mmH BnH 64H llH n = MIDI channel number: 0H-FH (ch.1-ch.16) mm = upper byte of parameter number specified by RPN (MSB) ll = lower byte of parameter number specified by RPN (LSB) * The value specified by RPN will not be reset even by messages such as Program Change or Reset All Controller. **RPN** The RPN (Registered Parameter Number) messages are expanded control changes, and each function of an RPN is described by the MIDI Standard. To use these messages, you must first use RPN MSB and RPN LSB messages to specify the parameter to be controlled, and then use Data Entry messages to specify the value of the specified parameter. Once an RPN parameter has been specified, all Data Entry messages received on that channel will modify the value of that parameter. To prevent accidents, it is recommended that you set RPN Null (RPN Number = 7FH/7FH) when you have finished setting the value of the desired parameter. On the HP 147R, RPN can be used to modify the following parameters. RPN Data entry MSB LSB MSB LSB Explanation 00H 01H mmH llH Master Fine Tuning mm, ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99.99 cents), Initial Value = 40 00H (±0 cent) 7FH 7FH --- ---RPN null Set condition where RPN and NRPN are unspecified. The data entry messages after set RPN null will be ignored. (No Data entry messages are required after RPN null). Settings already made will not change. mm, ll: ignored Copyright © 2000 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. .Program Change Status 2nd byte CnH ppH n = MIDI channel number: 0H-FH (ch.1-ch.16) pp = Program number: 00H...24H (prog.1...prog. 37) Received program change message are assigned as follows. prog. tone 1 Piano 4 Harpsichord 6 Electric Piano 8 Pipe Organ 9 Strings 11 Piano + Harpsichord 13 Piano + Electric Piano 15 Piano + Pipe Organ 16 Piano + Strings 24 Harpsichord + Electric Piano 26 Harpsichord + Pipe Organ 27 Harpsichord + Strings 33 Electric Piano + Pipe Organ 34 Electric Piano + Strings 37 Pipe Organ + Strings * 11-37 are in Dual Play mode. * Any Program Number other than those listed above that are received by the HP 147R are ignored. * After a Program Change message is received, the sound will change beginning with the next Note-on. Voices already sounding when the Program Change message was received will not be affected. ¦Channel Mode Messages .Reset All Controllers (Controller number 121) Status 2nd byte 3rd byte BnH 79H 00H n = MIDI channel number: 0H-FH (ch.1-ch.16) *When this message is received, the following controllers will be set to their reset values. Controller Reset value Expression 127 (max) Hold 1 0 (off) Sostenuto 0 (off) Soft 0 (off) .Local Control (Controller number 122) Status 2nd byte 3rd byte BnH 7AH vvH n = MIDI channel number: 0H - FH (ch.1 - ch.16) vv = Value: 00H, 7FH (0, 127) 0 = OFF, 127 = ON .All Notes Off (Controller number 123) Status 2nd byte 3rd byte BnH 7BH 00H n = MIDI channel number: 0H-FH (ch.1-ch.16) *When All Notes Off is received, all notes on the corresponding channel will be turned off. However if Hold 1 or Sostenuto is ON, the sound will be continued until these are turned off. .OMNI OFF (Controller number 124) Status 2nd byte 3rd byte BnH 7CH 00H n = MIDI channel number: 0H-FH (ch.1-ch.16) * The instrument will behave in the same way as it does when an “All Notes Off” message is received. The mode will be OMNI OFF, POLY (Mode 3). .OMNI ON (Controller number 125) Status 2nd byte 3rd byte BnH 7DH 00H n = MIDI channel number: 0H-FH (ch.1-ch.16) * The instrument will behave in the same way as it does when an “All Notes Off” message is received. The mode will be OMNI ON, POLY (Mode 1). .MONO (Controller number 126) Status 2nd byte 3rd byte BnH 7EH mmH n = MIDI chan...