Évaluations - 2, GPA: 4
(
)
)
|
Facilité d'utilisation
Bpf: The wah effect will be applied over a narrow frequency range. 2 Manual #2 0-127 0-127 Adjusts the center frequency at which the effect is applied. 3 Peak 0-127 0-127 Adjusts the amount of the wah effect that will occur in the range of the center frequency. Set a higher value for Q to narrow the range to be affected. 4 Sens 0-127 0-127 Adjusts the sensitivity with which the filter is controlled. 5 Polarity 0-1 Up, Down Sets the direction in which the frequency will change when the autowah filter is modulated. Up: The filter will change toward a higher frequency. Down: The filter will change toward a lower frequency. 6 Rate Mode 0-1 Hz, note When this is set to “note,” the effect is synchronized with the tempo. 7 Rate #1 1-127 0.05-10.00 Hz Frequency of modulation (Hz) 8 Rate 0-21 note Frequency of modulation (note) 9 Depth 0-127 0-127 Depth of modulation 10 Phase 0-90 0-180 deg Adjusts the degree of phase shift of the left and right sounds when the wah effect is applied. 11 Low Gain 0-30 -15 - +15 dB Gain of the low range 12 High Gain 0-30 -15 - +15 dB Gain of the high range 13 Level 0-127 0-127 Output Level No Parameter Value Description 1 Split Freq 0-16 200-8000 Hz Frequency at which the low and high ranges will be divided 2 Low Pre Delay 0-125 0.0-100.0 ms Delay time from when the original sound is heard to when the low- range flanger sound is heard 3 Low Rate Mode 0-1 Hz, note When this is set to “note,” the effect is synchronized with the tempo. 4 Low Rate #1 1-127 0.05-10.00 Hz Rate at which the low-range flanger sound is modulated (Hz) 5 Low Rate 0-21 note Rate at which the low-range flanger sound is modulated (note) 6 Low Depth 0-127 0-127 Modulation depth for the low-range flanger sound 7 Low Phase 0-90 0-180 deg Spaciousness of the low-range flanger sound 8 Low Feedback 0-98 -98 - +98% Proportion of the low-range flanger sound that is to be returned to the input (negative values invert the phase) 9 High Pre Delay 0-125 0.0-100.0 ms Delay time from when the original sound is heard to when the high-range flanger sound is heard 10 High Rate Mode 0-1 Hz, note When this is set to “note,” the effect is synchronized with the tempo. 21 .. . 0126: Auto Pan Adds a vowel character to the sound, making it similar to a human voice. Cyclically modulates the stereo location of the sound. No Parameter Value Description 1 Drive Sw 0-1 Off, On Turns Drive on/off. 2 Drive #2 0-127 0-127 Degree of distortion Also changes the volume. 3 Vowel1 0-4 a, e, i, o, u Selects the vowel. 4 Vowel2 0-4 a, e, i, o, u Selects the vowel. 5 Rate Mode 0-1 Hz, note When this is set to “note,” the effect is synchronized with the tempo. 6 Rate 1-127 0.05-10.00 Hz Frequency at which the two vowels switch (Hz) 7 Rate #1 0-21 note Frequency at which the two vowels switch (note) 8 Depth 0-127 0-127 Effect depth 9 Input Sync Sw 0-1 Off, On Determines whether the LFO for switching the vowels is reset by the input signal (ON) or not (OFF). 10 Input Sync Threshold 0-127 0-127 Volume level at which reset is applied 11 Manual 0-100 0-100 Point at which Vowel 1/2 switch 49 or less: Vowel 1 will have a longer duration. 50: Vowel 1 and 2 will be of equal duration. 51 or more: Vowel 2 will have a longer duration. 12 Low Gain 0-30 -15 - +15 dB Gain of the low frequency range 13 High Gain 0-30 -15 - +15 dB Gain of the high frequency range 14 Pan 0-127 L64 - 63R Stereo location of the output 15 Level 0-127 0-127 Output level No Parameter Value Description 1 Mod Wave 0-4 Tri, Sqr, Sin, Saw1, Saw2 Modulation Wave Tri: Triangle wave Sqr: Square wave Sin: Sine wave Saw1/2: Sawtooth wave 2 Rate Mode 0-1 Hz, note When this is set to “note,” the effect is synchronized with the tempo. 3 Rate #1 1-127 0.05 -10.00 Hz Frequency of the change (Hz) 4 Rate 0-21 note Frequency of the change (note) 5 Depth #2 0-127 0-127 Depth to which the effect is applied 6 Low Gain 0-30 -15 - +15 dB Gain of the low range 7 High Gain 0-30 -15 - +15 dB Gain of the high range 8 Level 0-127 0-127 Output Level . 012c: Slicer By applying successive cuts to the sound, this effect turns a conventional sound into a sound that appears to be played as a backing phrase. This is especially effective when applied to sustain-type sounds. . 012b: Ring Modulator This is an effect that applies amplitude modulation (AM) to the input signal, producing bell-like sounds. You can also change the modulation frequency in response to changes in the volume of the sound sent into the effect. No Parameter Value Description 1 Frequency #1 0-127 0-127 Adjusts the frequency at which modulation is applied. 2 Sens 0-127 0-127 Adjusts the amount of frequency modulation applied. 3 Polarity 0-1 Up, Down Determines whether the frequency modulation moves towards higher frequencies (Up) or lower frequencies (Down). 4 Low Gain 0-30 -15 - +15 dB Gain of the low frequency range 5 High Gain 0-30 -15 - +15 dB Gain of the high frequency range 6 Balance #2 0-100 D100:0W D0: 100W Volume balance between the direct sound (D) a...