Évaluations - 1, GPA: 4
(
)
)
|
Facilité d'utilisation
When powering down: Turn off the power to your guitar amp first. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * When operating on battery power only, the unit’s indicator will become dim when battery power gets too low. Replace the battery as soon as possible. Operating the Unit 654 3 1. When you have made the necessary connections, set the knobs as shown in the illustration. 2. Depress the pedal switch to turn the effect on. (Make sure the CHECK indicator lights.) 3. Adjust the depth of the Distortion effect using the DIST knob and GAIN BOOST knob. * Turning both knobs all the way up will result in increased noise. 4. Adjust the tone using the TONE knob. 5. Adjust the degree of low-end boost with the BOTTOM knob. 6. Adjust the LEVEL knob so that the level of the sound obtained when the effect is on is equal to that obtained when it is off. Changing the Battery When the indicator goes dim or no longer lights while an effect is on, it means that the battery is nearly dead and must be replaced. Replace the battery following the steps below. Thumbscrew Pedal Spring Base Battery Snap Cord Coil Spring Guide Bush Hole Battery Snap 9V Battery Battery Housing 1. Loosen the thumbscrew at the front of the pedal, then lift the pedal upwards to open the unit. * The thumbscrew can be left in the pedal while changing the battery. 2. Remove the old battery from the battery housing, and remove the snap cord connected to it. 3. Connect the snap cord to the new battery, and place the battery inside the battery housing. * Be sure to carefully observe the battery's polarity (+ versus -). 4. Slip the coil spring onto the spring base on the back of the pedal, then close the pedal. * Carefully avoid getting the snap cord caught in the coil spring. 5. Finally, insert the thumbscrew into the guide bush hole and fasten it securely. Troubleshooting Power won’t come on/ CHECK indicator doesn’t light: . Is the specified adaptor (PSA-series; sold separately) properly connected? Check the connection once more (p. 7). . Is the battery low or dead? Replace with a new battery (p. 10). . Is the guitar connected properly to the INPUT jack? Check the connection once more (p. 7). * To prevent excess battery drainage, turn the power on without the plug inserted in the INPUT jack. * The battery that was supplied with the unit is for temporary use-intended primarily for testing its operation. For using the unit for more extended periods of time, we recommend the use of alkaline batteries. * The CHECK indicator is designed for providing information about effects—such as their on/off status. It does not indicate whether the power is on or off. No sound / Low volume: . Is the MD-2 properly connected to your instrument? Check the connection once more (p. 7). . Could the LEVEL knob be turned too far down? The further counterclockwise you turn the LEVEL knob, the more the volume is reduced when the effect is on. Turn the LEVEL knob clockwise. . Is the volume turned down on any guitar amp or effects device you have connected? Setting Samples MD-2 Standard Sound Powerful Low Boost Overdrive Solid Distortion Specifications MD-2: Mega Distortion Nominal Input Level...................-20 dBu Input Impedance..........................1 M . Nominal Output Level................-20 dBu Output Impedance ......................1 k . Equivalent Input Noise Level....-110 dBu (IHF-A, Typ.) Controls.........................................Pedal Switch, GAIN BOOST Knob, DIST (distortion) Knob, TONE Knob, BOTTOM Knob, LEVEL Knob Indicator........................................CHECK Indicator (Serves also as battery check indicator) Connectors....................................INPUT Jack, OUTPUT Jack, AC Adaptor Jack (DC 9 V) Power Supply...............................DC 9 V; Dry battery (9 V type) S-006P/9 V (6F22/9 V) Dry battery (9 V type) 6AM6/9 V (alkaline) AC Adaptor (PSA-series: optional) Current Draw ...............................18 mA (DC 9 V) * Expected battery life under continuous use: Carbon: 18 hours These figures will vary depending on the actual conditions of use. Specifications Dimensions...................................70 (W) x 125 (D) x 55 (H) mm 2-3/4 (W) x 4-15/16 (D) x 2-3/16 (H) inches Weight ...........................................410 g/ 15 oz (including battery) Accessories....................................Owner's Manual, Leaflet (“USING THE UNIT SAFELY,” “IMPORTANT NOTES,” and “Information”) Dry battery (9 V type) S-006P/9 V (6F22/9 V) * The battery that was supplied with the unit is for temporary use-intended primarily for testing its operation. Options..........................................AC Adaptor: PSA-series * 0 dBu = 0.775 Vrms * In the interest of product improvement, the specifications and/or appearance of this unit are subject to cha...